| Incremental Forming |
| 101 |
Spherical Incremental Stretching of Sheet Metals by CNC Incremental Forming Process |
Kimiyoshi Kitazawa & Tetsuya Oka |
| 102 |
Incremental Flattening of Beaded Panels |
Kimiyosi Kitazawa & Hideki Hase |
| 103 |
Mechanisms of Flattening and Thickening in Incremental Process for Restoring Metal Cases to Sheet Metal |
Kimiyoshi Kitazawa & Hikaru Yamamoto |
| 104 |
Hemispherical Drawing by Incremental Hammering |
Daisuke Fujita, Yutaka Imaida & Tadashi Hasebe |
| 105 |
An Approximate Calculation Method for Forming Limit of Incremental Bulging Using High Speed Water Jet |
Hideo Iseki & Hidetaka Nishi |
| 106 |
Incremental forming of pure titanium dental plate (Distortion of the plate after trimming) |
Shigekazu Tanaka, Tamotsu Nakamura, Kunio Hayakawa, Nakamura Hideo, Kazuo
Motomura, Shinji Yamada & Okentarou Kushima |
| 107 |
Incremental Forming Process with Opposite Two Forming Styluses |
Shigekazu Tanaka, Tamotsu Nakamura & Kunio Hayakawa |
| Bending |
| 108 |
Effect of Forming Conditions on Springback in Bending of Aluminum Alloy Sheets |
Keita Akita, Ken-ichiro Mori & Kenji Yamada |
| 109 |
Strength Differential Effect and Bending Characteristics of Ultra Thin Copper Sheet for Electronic Parts |
Toshihiko Kuwabara, Akira Sekine, Kazuhiko Fukamachi & Ikuya Kurosaki |
| 110 |
Development of Spring-backless Right Angle V-bending Method of Sheet Metal |
Hideo Ogawa, Kento Shigeishi & Junichi Koyama |
| 111 |
Die Modification Method by a Simple Prediction of Spring-backed Geometry |
Tetsuya Kondo, Koich Ito & Yasutomo Nagai |
| 112 |
Instrumentation System for V-bending Process Using Die-embedded Micro-sensors Vol.2 The Optimization Design of The Sensor System. |
Ming Yang, Junichi Koyama, Kazunari Imai & Yuusuke Kageyama |
| 113 |
Relationship between Coil Breaks and Upper / Lower Yield Point of Steel Sheets |
Kajihara Takehiro, Matoba Tetsu & Itai Saburou |
| 114 |
Effect of Strip Material on Behavior of Incremental In-plane Bending |
Yingjun Jin, Takashi Kuboki & Makoto Murata |
| 115 |
FEM Simulation of Deformation Behaviour of Al Foam Sandwich Construction |
Kuniaki Matsuya, Hidenori Yoshimura, Kazunari Shinagawa, Yutaka Mihara,
Yoshihiro Sukegawa & Katsuhiko Murakami |
| Sheet Metal Forming |
| 116 |
Formulation of Proposed Shell Element- Shell Element for Numerical Spring-back Prediction of High Precision (1st Report) - |
Noritoshi Iwata, Hideo Tsutamori, Hiroshi Ishikura, Yasuyoshi Umezu, Atsunobu
Murata, Yasuhiro Yogo & Takanori Suwa |
| 117 |
Measurement of Strain Distribution along Thickness Direction under Strong Bending Deformation - Shell Element for Numerical Spring-back Prediction of High Precision (2nd Report) - |
Atsunobu Murata, Noritoshi Iwata, Hiroshi Ishikura, Hideo Tsutamori, Shintaro
Igarashi, Yasuhiro Yogo & Yasuyoshi Umezu |
| 118 |
Implementation to FEM and Verification in U and Hat-shape Bending - Shell Element for Numerical Spring-back Prediction of High Precision (3rd Report) - |
Noritoshi Iwata, Hiroshi Ishikura, Hideo Tsutamori, Yasuyoshi Umezu, Atsunobu
Murata, Yasuhiro Yogo & Takanori Suwa |
| 119 |
Effects of Material Model on Spring Back Simulation. |
Eiji Isogai, Tohru Yoshida, Noriyuki Suzuki , Akihiro Uenishi & Yukihisa
Kuriyama |
| 120 |
Twisting Mechanism of High Strength Steel in Sheet Metal Forming. |
Tohru Yoshida, Takashi Ariga, Seiichi Daimaru, Yasuharu Tanaka, Shunji
Hiwatashi & Yukihisa Kuriyama |
| 121 |
Development of Surface Deflection Evaluation Methodology by Using Curvature Technique |
Takeshi Moriya & Susumu Takahashi |
| 122 |
Effects of Work Strains by Bulge Forming on Shape Recovery Characteristics for Thin Plate of Ferrous Shape Memory Alloy |
Manabu Wada, Hisashi Naoi, Tadakatsu Maruyama & Tohru Yoshida |
| 123 |
Effect of Working Speed on Forming of Ni-Cr Alloy Strip |
Keiji Suzuki |
| 124 |
Friction Aided Deep Drawing of Magnesium Alloy Sheets in Room Temperature |
Norio Takakura, Sinichi Miyose, Takashi Iizuka & Katsuhiko Yamaguchi |
| 125 |
Drawability of Aluminum Alloy Sheets with Small Asperities formed by Embossing |
Norio Takakura, Kenji Narita, Takashi Iizuka & Katsuhiko Yamaguchi |
| 126 |
Development of High-efficiency Aluminum Blow Forming Process and Automotive Application. |
Kei Kiyama, Manabu Maruyama, Keiichiro Nakao & Yoshiaki Nakagawa |
| 127 |
A Study of Non-Lubricating Forming on Sheet Metal -Application to Deep Drawing (2nd Report)- |
Noriaki Iguchi, Yukihiko Uchida & Michihiko Hoshino |
| 128 |
Direct Observation of Interface between Tool and Workpiece in Sheet Metal Forming under Sliding-Bending Condition |
Akira Azushima, Motohiro Inagaki & Megmi Sakuramoto |
| 129 |
Friction Behavior in Dry Forming of Pre-coated Aluminum Sheets (1st Report : Effect on Contact Pressure and Sliding Velocity) |
Yoshinari Kikuta |
| 130 |
A Study on Process Design Methods of Redrawing Rectangular Cups |
Isobe Kunio |
| 131 |
A Study on Sheet Hydroforming By Using High Strength Steel Sheet |
Takanobu Saito, Takaaki Hira, Yuji Yamasaki & Akihide Yoshitake |
| 132 |
The Forming Characteristic of Sheet in The Explosive Forming |
Takeshi Hinata, Hirofumi Iyama & Shigeru Itoh |
| 133 |
Simulation of Sheet Hydroforming by Static Explicit Finite Element Method |
Hiroshi Utsugi, Motoo Asakawa, Tomohiro Hatakeyama, Takayuki Hama, Akitake
Makinouchi, Hiroyuki Amino & Lu Yan |
| 134 |
Evaluation of Shape Accuracy of Cylindrical Cups Formed by Stretching and Deep Drawing. |
Keita Kawachi, Yosihiro Goto, Takayuki Muranaka & Norio Ito |
| 135 |
Square Shells Deep Drawing of Different Thickness Tailored Blanks Using Counter Punch |
Yuki Morishita, Yasuhiro Sakamoto & Shigeki Abe |
| 136 |
Development of a multi-point support system for a deep drawing die, --Improvement of the product accuracy by the relocation of supporting cells |
Takahiro Ohashi |
| 137 |
Production of Deep Cups with Wide Flange from Developed Blanks |
Norio Takakura, Yuki Muroya, Takashi Iizuka & Katsuhiko Yamaguchi |
| Form rolling |
| 201 |
Thread Rolling of Antiloosening Bolt Fastenings Based on Double Threading Mechanism |
Teruie Takemasu & Toshinaka Shinbutsu |
| 202 |
Forming Process of Rolled Antiloosening Double Threading Bolt Fastenings and Its Performance Evaluation |
Teruie Takemasu & Toshinaka Shinbutsu |
| 203 |
Form Rolling of Micro Grooves |
Masahito Yamamoto, Shuichi Amano, Noriaki Hishida, Teruie Takemasu, Toshihiko
Kuwabara & Toshinaka Shinbutsu |
| Forging |
| 204 |
Effects of Tool Motion in Rocking Die Forging |
Toshiyuki Oyama & Tooru Kawabe |
| 205 |
About the Relationship between Die Shapes and Upset Load using the simulation of the RR Forging |
Hideki Kakimoto, Takashi Choda, Takahashi Youichi & Hiroyuki Mori |
| 206 |
Isothermal Forging of ODS Ni-based Super Alloys |
Shin Sugiyama, Jun Sugiyama & Kiyoyuki Ohuchi |
| 207 |
Effect of Forging Parameter on Die Damege Development of Die Damege Prediction System 3 |
Takafumi Sakai, Shigekazu Ito, Hiroaki Yoshida, Sachihiro Isogawa &
Munenori Ono |
| 208 |
Effect of Bilet-height on Load and Metal Flow in Combined Extrusion |
Eisuke Murai & Munenori Ono |
| 209 |
Analyses of Upsetting by Using the Point Collocation Method with a Boundary Layer of Finite Elements |
Yongming Guo, Yasuto Yokouchi & Kenji Nakanishi |
| 210 |
Development of the Object-Oriented-like Interface (Development of the Modern Interface for FEM analyses of Plastic Workings –3) |
Yoshida Tadatsugu |
| 211 |
Effect of Punch Shape on Forming Limit of Magnesium Alloy in Cold Forging |
Ryo Matsumoto, Tomoo Kubo & Kozo Osakada |
| 212 |
Forming of Boss for AZ31 Magnesium Alloy Sheets. |
Nobuhiro Koga, Chihyang Kuan, Nobumasa Yugi & Ratchanee Paisarn |
| 213 |
Forging Test of Aluminum Alloys by Using Multi-Axes Material Testing Machine |
Kanichi Hatsukano, Kunio Matsuzaki, Toru Shimizu & Kichitaro Shinozaki |
| 214 |
Detection of Damage and Fracture of Die in Bolt Parts Former by Fractal Characteristics of AE |
Kunio Hayakawa, Tamotsu Nakamura, Shigekazu Tanaka, Takuya Nozue &
Kazumi Saitoh |
| Laser Forming |
| 215 |
Effect of Laser Irradiation Mode on Thickening of Pipe in Die-less Wall Thickening with Local Heating by Laser |
Ryo Matsumoto, Yohei Umino & Kozo Osakada |
| 216 |
Bending of High Tensile Strength Steel Sheets by Laser Forming |
Masaaki Otsu & Keizo Ogata |
| 217 |
Bending of AZ31 Magnesium Alloy Foils by Laser Forming |
Masaaki Otsu, Hideo Benoki & Eiji Taki |
| 218 |
Effect of Heat Treatment on Bending Angle in Laser Forming of Pure Titanium Foil |
Masaaki Otsu, Yasuhiro Ito, Akira Ishii & Hideshi Miura |
| Powder Forming |
| 219 |
Fabrication of Copper and Aluminum Alloys Model by Laser Prototyping |
Yoshitsugu Noshi, Edson Costa Santos, Masanori Shiomi, Kozo Osakada &
Humie Abe |
| 220 |
Fabrication of Functionally Graded Cemented Carbide Models by Powder Layer Compaction |
Shinya Nose, Kozo Osakada, Masanori Shiomi & Yoshiaki Mizukami |
| 221 |
A Constitutive Model for Pressure Sintering of Metallic Hollow Spheres Compared to Firing Experiment of Compacts |
Kazunari Shinagwa, Hidenori Yoshimura, Yutaka Mihara, Yoshihiro Sukegawa
& Katsuhiko Murakami |
| 222 |
Forming of Dam Sedimentary Soil |
Kimiyoshi Kitazawa, Yukihiro Kaneko, Kozima Hirohumi & Yorikuni Shibuya |
| 223 |
Effect of Nickel Particle Size on Microstructure of Ni/YSZ Cermets |
Takehisa Tsurumaki, Yusuke Ayame, Keiou Nishimura, Zhongchun Chen &
Keisuke Ikeda |
| 224 |
High-Temperature Stability of Alumina Fiber-Reinforced Alumina Matrix Composites |
Tomohide Tamachi, Keiou Nishimura, Zhongchun Chen & Keisuke Ikeda |
| 225 |
Fabrication of SKD11 Powder by Selective Laser Melting. |
Masaaki Otsu, Tomonori Fukunaga, Akitaka Tanaka, Takuro Setoyama &
Hideshi Miura |
| 226 |
Fabrication of a Magnetic Composite Material by Use of Magnesium-Alloy Superplastic Powder |
Kunio Okimoto & Kazuki Fujimoto |
| 227 |
Bonded Magnet Fabricated by Resin Impregnation |
Kunio Okimoto & Kazuki Fujimoto |
| 228 |
Controlling cell morphology of porous Al and blowing behavior in a mold |
Makoto Kobashi & Naoyuki Kanetake |
| 229 |
Effect of Working Condition on Bi-Te Thermoelectric Materials Fabricated by Compressive Torsion Loading |
Masataka Hamaguchi, Takashi Ito & Naoyuki Kanetake |
| Shearing |
| 230 |
Deformation Analysis for Axisymmetric Blanking: Deformation Analysis for Shaving Process of High Strength Steel |
Yoshinori Yoshida, Daisuke Okushita, Nobuki Yukawa & Takashi Ishikawa |
| 231 |
FEM Simulation of Incremental Shearing by Conventional Method |
Nobuo Hatanaka, Katsuhiko Yamaguchi, Norio Tatakura & Takashi Iizuka |
| 232 |
Presumption of Empty Shutting Load And Single Fiber Cutting Load of Beauty Scissors |
Kenji Inoue, Mitsugu Motomura, Takashi Iimura & Tetsuya Sonoda |
| 233 |
The Influence Which Is Given by Some Parameters of The Beauty Scissors to The Hair Cutting Side |
Kenji Inoue, Mitsugu Motomura, Takashi Iimura & Tetsuya Sonoda |
| 234 |
FEM Analysis of Clearance Compensation Effect in Shearing. |
Koura Naoki, Sasada Masahiro & Aoki Isamu |
| 235 |
Fundamental Study on Small Hole Piercing |
Hitoshi Kobayashi, Masahiro Sasada & Isamu Aoki |
| 236 |
FEM Analysis of Material Slip on Shearing Tools (5th Report: FEM Analysis and Experiment on Tool Wear) |
Masao Murakawa, Sutasn Thipprakmas & Masahiko Jin |
| 237 |
FEM Simulation of Fine Blanked Surface |
Sutasn Thipprakmas, Masahiko Jin & Masao Murakawa |
| Lumber |
| 301 |
Transparent Phenomena in Compressed Wood |
Kimiyoshi Kitazawa, Yorikuni Shibuya, Hirofumi Kojima & Naoyuki Kitamura |
| 302 |
Propagation of Crushing the Cells in Japanese Cedar under Radial Compression |
Kimiyoshi Kitazawa, Hirotsugu Kobayashi, Yorikuni Shibuya & Hirofumi
Kojima |
| 303 |
Permanent Shape Fixation Phenomenon by Low Temperature Heat Treatment of Sugi Compressed Wood |
Kitamura Naoyuki, Kitazawa Kimiyoshi, Shibuya Yorikuni & Kojima Hirohumi |
| 304 |
Compressed Wood of Dead Pine Lumber Impregnated with Metals |
Kimiyoshi Ktazawa, Seiji Amino, Yorikuni Shibuya & Hirohumi Kojima |
| 305 |
Crushing the Tissues in Bamboo under Radial and Tangential Compressions |
Kimiyosi Kitazawa & Keisuke Kano |
| 306 |
Why Does Crack Arrest in Compressed Wood? |
Kimiyoshi Kitazawa, Kozue Takaki, Yorikuni Sibuya & Hirofumi Kojima |
| 307 |
Set Mechanism of Compressed Wood |
Kimiyoshi Kitazawa , Takeshi Ueyama , Hirofumi Kojima & Yorikuni Shibuya |
| 308 |
How Much Water Does Compressed Wood of Dead Pine Lumber Absorb? |
Kimiyoshi Kitazawa, Hirofumi Kojima, Yorikuni Shibuya & Keiko Hanashi |
| 309 |
Manufacturing of Two-Directional-Three-Steps Compressed Wood |
Tetsumaro Hiroi, Osamu Hasegawa & Hisashi Nishimura |
| 310 |
Possibility and Problems in Injection Moulding of Wood Powders with Conventional Moulding Machine for Polymers |
Tsunehisa Miki, Norio Takakura, Takashi Iizuka, Katsuhiko Yamaguchi &
Kouzou Kanayama |
| 311 |
Spray Forming of Waste Paper |
Kimiyosi Kitazawa & Fujimura Atsushi |
| 312 |
Development of Green Composite with Natural Fiber |
Minami Kimura, Ryosuke Matsumoto & Katsuyuki Namiki |
| Material Model |
| 313 |
Multi-Scale Analysis for Dual Phase Polycrystal Model considering Evolution of Dislocation Cell Structure |
Kouji Yokota, Yutaka Imaida & Tadashi Hasebe |
| 314 |
Multi-Scale Analysis of Detailed Structures and Mechanical Properties of Dislocation Cell Wall based on Discrete Dislocation Dynamics |
Satoru Goto, Yutaka Imaida & Tadashi Hasebe |
| 315 |
Multi-Scale Polycrystal Plasticity Analysis using Constitutive Equation considering Strain Gradients |
Yasuhiro Yamada, Tadashi Hasebe & Yutaka Imaida |
| 316 |
Multi-Scale Polycrystalline Plasticity Modeling for Dual Phase Materials based on Field Theory of Plasticity |
Hideaki Tamada, Yutaka Imaida & Tadashi Hasebe |
| 317 |
Phase-Field Simulation of Self-Assembling Quantum Dot |
Masafumi Inoue, Yutaka Imaida & Tadashi Hasebe |
| 318 |
Multi-Scale Polycrystalline Plasticity Modeling based on Bio-Inspired Mechanics |
Tadashi Hasebe |
| 319 |
A Dislocation Model for Anisotropy of Strain Hardening in Advanced Stage of Plastic Deformation |
Kenji Shouwaki |
| 320 |
Analysis of Dynamic Strain Ageing with Transportation of Solute Atom by Moving Dislocation |
Kenji Shouwaki |
| 321 |
Finite Element Analysis on Hydrostatic Pressure Dependent Polymers using Plastic Constitutive Equation with Kinematic Hardening |
Kunio Hayakawa, Yukio Sanomura & Mamoru Mizuno |
| 322 |
Elastic-Plastic Constitutitive Equation for Biaxial Drawn Polymers |
Yukio Sanomura, Kunio Hayakawa & Mamoru Mizuno |
| 323 |
Dependence of Stress-Strain Characteristics on Strain-Rate for Polycarbonate |
Yasuhisa Sato, Taku Ueno, Kengo Abe, Yuhki Uchimi, Daisuke Chiba &
Yuhji Hakoyama |
| 324 |
Stress-Strain Relationship in Inhomogeneous Elongation Range on Tensile Test of Sheet Metals |
Kenichi Hasegawa, Keiou Nishimura, Zhongchun Chen & Keisuke Ikeda |
| 325 |
Application of Multi-grid Method to Elasto-plastic FEM |
Hiroshi Fukiharu, Mizuki Sawada & Yasuto Yokouchi |
| 326 |
A Suitable Preconditioning Scheme for Elasto-plastic FEM |
Mizuki Sawada, Hiroshi Fukiharu & Yasuto Yokouchi |
| 327 |
Notched Plate Tension Test Using Image Analysis: Determination Method of Ductile Fracture Parameters (3nd report) |
Yoshinori Yoshida, Nobuki Yukawa & Takashi Ishikawa |
| 328 |
Effect of Stress-Strain Curve on Material constants in FEM-Based Determination Method for Ductile Fracture Criteria |
Hiroshi Koyama, Ken-ichi Manabe & Ken-ichi Kawai |
| 329 |
Determination of Flow Stress Covering to Large Strain Region by Finite Element Based on Inverse Analysis Technique |
Okuno Hiroto & Koeda Hideo |
| Extrusion |
| 330 |
Formability of AZ91 Compsites with SiC Produced by PM |
Kunio Matsuzaki, Kanich Hatsukano, Kotaro Hanada, Toru Shimizu & Masaharu
Takahasi |
| 331 |
Forming for Extruded plate of AZ31B Magnesium Alloy Cutting Chip with Port-hole Die |
Norio Takatsuji, Kenji Matsuki, Tetsuo Aida, Kazuo Murotani & Takamichi
Yashima |
| 332 |
Effects of Die Shape on Metal Flow in the Spreading Extrusion of the Magnesium Sheet with Shear Strain |
Yukihiko Uchida, Michihiko Hoshino & Kouji Awai |
| 333 |
Analysis of Metal Flow in Grooved Wheel during Conform Extrusion Process |
Yukihiko Uchida, Michihiko Hoshino & Kenichi Shimai |
| 334 |
Extrusion of Circular Tube with Variable Wall Thickness by using Tapered Mandrel and Die with Choke |
Takahiro Makiyama, Hirokazu Takaoka, Takashi Kuboki & Makoto Murata |
| 335 |
Deformation Analysis of Shaped Bars with Various Curvatures Using Extrusion Process through Inclined Die Aperture |
Shigefumi Kihara, Shunsuke Miyoshi, Mitsunobu Shiraishi & Masato Niikawa |
| 336 |
Forming for Inside Spiral Multi-Grooved Tube by Hot Extrusion |
Norio Takatsuji, Nobuyuki Higashi, Kenji Matsuki, Tetsuo Aida, Kazuo Murotani
& Yutaka Hasegawa |
| 337 |
Development of Extusion System for Forming Helical Teeth on Surface of Hollow Shaft |
Mitsunobu Shiraishi, Kensuke Kuroki & Yoshihiro Goto |
| 338 |
Shaping of Spur Gear by Cold Extrusion of Carburized and Normalized Steel Workpiece |
Hajime Yoshida, Yozo Sawaki, Yoshihisa Sakaida & Tadashi Suzuki |
| Tube forming |
| 401 |
Finite Element Simulation of Tube Shear Bending Process |
Goodarzi Mohammad, Kuboki Takashi & Murata Makoto |
| 402 |
Influence of Working Conditions on Stress in Nosing Process |
Yasuhiko Kimura, Takashi Kuboki, Makoto Murata & Shimoda Takeshi |
| 403 |
Influence of Processing Course on Sppining of Square Pipe |
Hitomi Aro, Makoto Murata, Takashi Kuboki & Shunsuke Hiraki |
| 404 |
Effects of Expanding Process on Shape Recovery Characteristics for Pipe Joint of Ferrous Shape Memory Alloy |
Yoshinori Joto, Kouhei Narita, Hisashi Naoi & Takashi Kurita |
| 405 |
Characteristics of Energy Absorption for Aluminum Pipes by Axial Compression |
Takahiro Kurosawa, Hideo Kajino, Terumasa Tumura & Hisashi Naoi |
| 406 |
Study on Intrusion Bending for Thin Wall Steel Tubes |
Naoki Kitakami, Tetuaki Sano, Hisashi Naoi, Masaaki Mizumura & Yukihisa
Kuriyama |
| 407 |
Study on Shape of Mandrel for Hot Mandrel Bending |
Soshi Kawanishi, Soon-tae Jang, Hisashi Naoi, Hiromi Sakai & Takashi
Kurita |
| 408 |
Research of Bending Method for the Magnesium Tubes(Part2)-Deformation Characteristics of Magnesium Tubes Made by Intrusion Bending with Induction Heating- |
Takaya Motoharu, Banno Kimihiko, Naoi Hisashi & Seto Yoshiki |
| 409 |
A Study on Biting Deformation in Crashing Process of Tube Hydroforming Applying FEA |
Koji Suzuki, Masaru Fukumura, Yu Qiang & Masaki Shiratori |
| 410 |
Finite-Element Simulation of Deformation Features of Welded Bellows with Inclined Part at External Edge |
Takuo Nagamachi, Mishiba Takashi & Katsuhiro Katsuki |
| 411 |
Effect of Forming Conditions on Deformation Behavior in Hammering Hydroforming of Tube |
Tomoyoshi Maeno, Ken-ichiro Mori & Seijiro Maki |
| 412 |
Effects of Material Properties on Hydroforming after Bending |
Masaaki Mizumura & Yukihisa Kuriyama |
| 413 |
Formability of Cold Drawn and Normalized Steel Pipes under Free Bulge Forming |
Kyousuke Moriguchi & Toshihiko Kuwabara |
| 414 |
Analysis of Forming Limit Stresses for Combined Strain Paths |
Kengo Yoshida & Toshihiko Kuwabara |
| Sheet Metal Forming |
| 415 |
Influence of Thickness of AZ31 Magnesium Alloy Sheets on Their Dent Resistance |
Daisuke Igarashi, Yukutake Eitaro, Masahiro Kubota, Makoto Sugamata &
Junichi Kaneko |
| 416 |
Trial Manufacture Adapted Worm Forming of Magnesium Allioy |
Minami Kimura & Shinichi Kato |
| 417 |
Embossing using Superplastic Aluminum Alloy |
Minami Kimura & Tomouki Kizaki |
| 418 |
Effect of Thickness of Alminum Foil on the Defomation Behavior |
Shoji Imatani & Yutaka Wakasu |
| Production system |
| 419 |
Case and Viewpoint of Monodukuri Design Method |
Hiroya Murakami, Keiichi Nakamura & Shinji Tanaka |
| 420 |
Precision Parts Manufacturing Using Rubber Die Molding of Carbon Fiber Reinforced Plastic |
Minami Kimura & Masao Kobayashi |
| 421 |
Mechanism of Separation Machinary |
Minami Kimura |
| Fiber Reinforced Plastic |
| 422 |
Strength of Hybrid Matrix FRP |
Kimura Minami & Nagai Kei |
| 423 |
Development of Simple Molding for CFRTP and Its Trial Parts |
Minami Kimura & Kota Hiraii |
| 424 |
Development of CFRP Engine Parts Manufacturing |
Minami Kimura, Tsuchiyama Yusuke & Akira Kobayashi |
| 425 |
Trial Manufacturing of Bicycle Parts using CFRP |
Minami Kimura & Takahiro Ishiguro |
| Material testing, Masterial character |
| 426 |
Influence of Purity and Prestrain on Ductile-Brittle Transition Behavior of Chromium |
Yasunori Harada |
| 427 |
SEM/EBSD in Situ Measurement of Uni-Axial Tensile Plastic Deformation of Pure-Iron Single Crystal |
Nakamachi Eiji, Morimoto Hideo, Enoki Shinichi & Kinoshita Taneyuki |
| 428 |
Investigation of Relationship between Material Flow and Micro-Crystal Structure in Cold Forging Processes by SEM/EBSD Observation |
Tsutao Katayama, Eiji Nakamachi, Yasunori Nakamura, Ichiro Nakasu, Shinichi
Enoki & Rie Kawamura |
| 429 |
Mechanical Properties of Rusty Mild Steel Sheet |
Nobukazu Hayashi & Masanori Kobayashi |
| 430 |
Cross Hardening Effect for Steel Sheets under Impact Loading |
Masahide Kawakami, Yutaka Imaida & Tadashi Hasebe |
| 431 |
High Temperature Tensile Properties of A Commercial Purity Titanium Cold-Rolled Severely |
Isao Kuboki |
| 432 |
Change in Micro-Hardness and Crystal Orientation during Tensile Plastic Deformation of Polycrystalline Pure Titanium |
Xiaoqun Wang, Takeji Abe, Naoya Tada & Tashiyuki Torii |
| 433 |
Prediction of Strain Aging Process Based on Microstructure in Medium Carbon Steel |
Akio Miyake, Megumi Takada, Takashi Kuboki & Makoto Murata |
| 434 |
Superplastic Blow Forming in Partial Clad Sheets |
Sumito Kojima & Takashi Ishikawa |
| Mashy-state Forming |
| 501 |
High Speed Roll Casting of Magnesium Alloy Strip. |
Yasuo Sugiura, Tetsuji Matsui, Tshio Haga, Takashi Ueyama & Masaaki
Ikawa |
| 502 |
Casting of Wrought Aluminum Alloy Strip by a High Speed Twin Roll Caster. |
Masaaki Ikawa, Toshio Haga, Noriya Ohama, Kaname Deguchi, Shinji Kumai
& Hisaki Watari |
| 503 |
Casting of Aluminum Alloy Strip by an Unequal Diameter Twin Roll Caster. |
Masaaki Ikawa, Toshio Haga, Hideki Inui, Shinji Kumai & Hisaki Watari |
| Special Theme Session: Sheet Metal Forming of Light Metals, Material Development |
| 504T |
Deep Drawing Test of AZ31 Magnesium Alloy Sheets at Room and Elevated Temperatures |
Yukutake Eitaro, Hiromitsu Oguchi, Junichi Kaneko, Makoto Sugamata &
Masahiro Kubota |
| 505T |
Strech-Flanging Formability and Fixability of AZ31 Magnesium Alloy Sheets at Elevated Temperatures |
Makoto Watanabe, Masao Matsui, Akio Kawabe, Yoshiki Tsubouti, Takasi Suzuki
& Yutaka Tsutida |
| 506T |
FE Analysis of Heating Conditions on Warm Deep drawing of Magnesium Alloy sheets |
Osamu Shimomura & Kenichi Manabe |
| 507T |
Effect of Temperature and Strain-Rate on Yield Behavior for AZ31 Sheets |
Tetsuo Naka, Tomohisa Hironaka, Masahide Kohzu, Kenji Higashi, Takeshi
Uemori & Fusahito Yoshida |
| 508T |
Effect of Texture on Mechanical Property and Formability under High Strain Rate in AZ31 Magnesium Alloy Sheet |
Tomohisa Hironaka, Shouta Nakastuka, Masahide Kohzu, Testuo Naka, Fusahito
Yoshida & Kenji Higashi |
| 509T |
Plastic Buckling Behavor of a Magnesium Alloy Pipe |
Izumi Fukuda, Yasunari Ohishi & Tutomi Murai |
| 510T |
FE Simulation of Springback deformation for Aluminium Alloy Sheets |
Kenji Yamada, Hideo Mizukoshi & Koushi Okada |
| 511T |
The Effect of Local Solution Treatment in the Forming using a Non-cylindrical Punch |
Takeshi Nishiwaki & Naoyuki Kanetake |
| 512T |
Effect of Anisotropic Yield Function on Sheet Forming Simulation of Miniature Fender Model for Aluminium Alloy Sheets |
Kenji Yamada, Mineo Asano, Hideo Mizukozhi & Koushi Okada |
| 513T |
Press Formability of Developed Hexagonal Dimple Pattern Sheet |
Masao Matsui, Hisayosi Kato, Yoshinori Suzuki, Takasi Suzuki, Masayuki
Kimura & Hitoshi Wada |
| 514T |
Press Forming and Shape Evaluation of Curved Hat High Strength Steel Channel |
Hiroshi Utsugi, Motoo Asakawa, Yuuki Mamitsuka, Hiroshi Yano, Yoshio Fujishiro
& Ikuhiko Hayashi |
| 515T |
Influence of Strength and Thickness on Material Properties of Steel Sheets during Continuous Tension-Unloading-Compression Process |
Tomohito Iwamoto, Masao Matsui, Toyoki Moriya, Hideo Tsutamori, Noritoshi
Iwata, Atsunobu Murata & Masami Iimi |
| Special Theme Session: Technology of Improvement on Quality and Precision in Forging |
| 516T |
The state of the art for Net Shaped forging in view of a tool manufacturer. |
Tatsuo Arima |
| 517T |
A Simple Measurement Method of Compression Behavior of Cemented Carbide for Cold Forging Die |
Zhrgang Wang, Hiroaki Shiraga, Naoharu Ueda, Takemi Matsumoto, Makoto Ohhashi
& Hiroshi Nakagaki |
| 518T |
Fatigue Crack Growth Behavior of Cemented Carbide Die in Cold Forging process |
Zhrgang Wang, Isao Nakashima, Naoharu Ueda, Makoto Ohhashi & Takemi
Matsumoto |
| 519T |
Investigation about Modification of Tribo-Testing Method Based on Combined Forward-Backword Straight Can Extrusion |
Tamotsu Nakamura, Shigekazu Tanaka, Kunio Hayakawa & Yoshihiro Sagisaka |
| 520T |
Finite Element Analysis on Cold Forging of Spur Gear Using Elastic Deformation of Die |
Tamotsu Nakamura, Kunio Hayakawa, Norihiko Ito, Hitoshi Ishida & Shigekazu
Tanaka |
| 521T |
Drawing/Upsetting Combination Cold Forging for Thick Cylindrical Tube |
Shinichi Enoki, Kenichi Akamatsu & Ichiro Nakasu |
| 522T |
Clad Gear Deformation by Cold Die Forging with Divided Metal Flow with Different Materials |
Kohzoh Katoh, Kazuyoshi Kondo & Kenji Satoh |
| 523T |
Formability of Aluminum Alloys and Compressing Punch Shape Under Gear Toothed Products Utilizing Divided Flow Method |
Kyoichi Ohga, Fumio Murakoshi, Hiroyuki Ando, Koji Miyoshi & Kazuyoshi
Kondo |
| 524T |
Detecting Method and Prediction of internal Crack in Aluminium Alloy Combined Extrusion of Rod |
Munenori Ono & Eisuke Murai |
| 525T |
Combined Forward-backward Extrusion with Controlled Exit Velocity |
Shinji Hanami, Kozo Osakada, Ryo Matsumoto, Masaaki Otsu, Tatsuya Watanabe
& Daishi Hayashida |
| 526T |
Thickening Process of Plate Using Deep Drawing and Plate Forging |
Yu Kawamura, Nobuki Yukawa, Yoshinori Yoshida & Takashi Ishikawa |
| 527T |
Study on Sheet Forging (1st Report: Investigation of Flanging Characteristics) |
Masao Murakawa, Masahiko Jin, Sutasn Thipprakmas, Tomokazu Kanaizuka &
Katuhiro Yamamoto |
| 528T |
Deformation Analysis for Surface Defects in Upset Forging (2nd Report) |
Taishi Sakai, Nobuki Yukawa, Yoshinori Yoshida & Takashi Ishikawa |
| 529T |
Trimming Process Simulation to Predict Dynamic Balance Values of Forged Crankshaft |
Shinichiro Fujikawa, Kazuhiro Mitamura, Masatoshi Izawa & Ryosuke Watanabe |
| 530T |
A Study of Forming Flange with Grooves or the Like in the Outer Surface by Using Thick Metal Plate -Application to Various Form (4th Report)- |
Hirokazu Chuukyou, Yukihiko Uchida, Michihiko Hoshino & Tetsuya Iwabuchi |
| Coining |
| 531 |
Fundamental Study on Ultrasonic Microcoining (2nd Report: Trial Fabrication of Herringbone Groove) |
Masahiko Jin, Shoichi Ishiwata, Mituru Kodama & Masao Murakawa |
| 532 |
Study on Micro Coining using Ultrasonic Vibration |
Hiroyuki Noguchi & Masao Murakawa |
| 533 |
Transferring Process of Micro-projection Patterns on Coinage Dies |
Hideaki Mori, Takashi Kawabe, Yoshinori Matsushita, Kazuhisa Amano, Akihiro
Fujiyama & Yasuyuki Fukuhara |
| Tribology |
| 534 |
Size Effect of Friction Coefficient in Micro Forging |
Zhrgang Wang, Dezhou Xue & Kuniaki Dohda |
| 535 |
Wear Property of Hard-coated High Speed Tool Steel |
Noihde Yotani & Kazuhiko Kitamura |
| 536 |
Mechanism of Reduction of Friction utilizing Ultrasonic Vibration (2nd Report) |
Kenji Tamaoki, Seiji Kataoka, Kenichi Gotoh & Akio Motoi |
| Rolling |
| 601 |
Effect of Elements in Cu-enriched Phase on Penetration into Grain Boundaries in Hot Working of Cu-bearing Steel |
Chihiro Nagasaki & Koji Shibata |
| 602 |
Prediction of Microstructure on Wire Rod Mill Line by Quasistatic Analysis. |
Sachihiro Isogawa, Masamichi Kawano & Masanao Fujiwara |
| 603 |
Improvement of Mechanical Property of Al-Mn Alloys by using resistance heat treatment |
Minoru Ishiguro, Seijiro Maki, Ken-ichiro Mori & Yasunori Makino |
| 604 |
Simulation of Deformation and Temperature in Mannesman Pierce Rolling |
Kazutake Komori |
| 605 |
Investigation on Tilting in Bar and Rod under Groove Rolling |
Shunsuke Ueki, Motoo Asakawa, Makoto Toi, Yuki Katayama & Kengo Kobayashi |
| 606 |
Deformation Analysis of Surface Flaw in Rolling of Bar and Wire |
Tetsuo Shinohara & Kazunari Yoshida |
| 607 |
Development of 3-dimensional Analysis Model on Repeated Bending |
Atsushi Aizawa, Kenji Hara, Kenichirou Maeda & Hiroyuki Ueda |
| 608 |
Beakage at the Edge of Mg Sheets in Cold Rolling |
Matsuo Ataka, Yuuki Sakurai, Jun Yanagimoto & Akira Yanagida |
| 609 |
Load and Sheet Vibration Characteristics during Cold Rolling with Ultra Sonic Oscillation |
Takao Kawanami, Akio Segawa & Kazunori Ban |
| 610 |
Development of Quantitative Evaluation Method with Plate-out Conditions |
Yoshiki Takahama, Toshiyuki Shiraishi & Shigeru Ogawa |
| 611 |
Effect of Tension on Heat Scratch in Cold Rolling |
Toshiyuki Shiraishi, Yoshiki Takahama & Shigeru Ogawa |
| 612 |
FE Simulation of Temper Rolling of Steel Strip in Consideration of Yield-Point Phenomena |
Yuuya Kaneda, Shigeo Yamamoto & Fusahito Yoshida |
| 613 |
Discussion About Transcription Of Roll Roughness On The Strip In Temper Rolling |
Matsuo Ataka, Yoshinori Aramaki & Takahiko Okamoto |
| 614 |
Surface Roughness Control of Calvanized Steel Sheet for Automobile |
Akinobu Ishiwatari, Katsuhiro Takebayashi, Kazunari Ono & Kazuhiro
Abotani |
| Micro Forming |
| 615 |
Load Characteristics of Rotation-Compression Forming for Improvement of Material Flow into Micro-Groove |
Katsuyuki Yoshikawa |
| 616 |
Evaluation of Micro Billets Made from Sheet Metal |
Kenji Hirota & Kyosuke Taguchi |
| 617 |
Replication of Flat Surface and Surface Microgeometry to Coated Workpiece by Coining |
Ike Hiroshi & Nakano Yusuke |
| 618 |
Superplastic Forming of Micro-Cantilevers for IC-Probe with Pt-Based Metallic Glass and Their Mechanical Properties. |
Yuichi Hirai, Dong Chen & Yasunori Saotome |
| 619 |
Ultrasonic Micro Piercing with High Aspect |
Mori Toishhiko & Kurimoto Sinji |
| 620 |
Critical Depth of Hard-Brittle Materials in Nano Forming Processes |
Yoshino Masahiko & Sivanandom Aravindan |
| 620 |
Critical Depth of Hard-Brittle Materials in Nano Forming ProcessesYoshino
Masahiko & Sivanandom Aravindan |
| High Energy Forming |
| 621 |
Micro Bending of AZ31 Foil by Spark Forming |
Masaaki Otsu & Yukari Katayama |
| 622 |
Experiments of Magnetic-Pressure Seam Welding for Practical Uses (2nd Report) |
Aizawa Tomokatsu, Okagawa Keigo & Kashani Mehrdad |
| 623 |
Impact Seam Welding with Magnetic Pressure for Aluminum Sheets (3rd Report) |
Keigo Okagawa, Tomokatsu Aizawa, Makoto Miyazaki, Yasuto Shindou, Shinji
Tanisho, Keisuke Kimura & Takashi Ooki |
| 624 |
Numerical Simulation of a Metal Plate by Explosive Forming |
Hirofumi Iyama, Takeshi Hinata & Shigeru Itoh |
| 625 |
Effect of Discharging Conditions on Shear Drop Forming in Hydro Spark Micro Punching for Thin Sheet Metals |
Daisuke Kunito, Yutaka Imaida & Tadashi Hasebe |
| 626 |
On 1 Micrometer-Order Forming by Hydro Spark Forming Method |
Taizo Honda, Yutaka Imaida & Tadashi Hasebe |
| 627 |
The Possibility of Explosive Welding Using Underwater Shock Wave. |
Akihisa Mori, Kazuyuki Hokamoto, Youhei Nara & Masahiro Fujita |
| 628 |
The Making of Various Composites through Dynamic Powder Compaction |
Jung-suk Lee, Kazuyuki Hokamoto, Sigeru Tanaka, Masatosi Watanabe &
Masahiro Fujita |
| Crash Requirement |
| 629 |
On Effect of Pressure Profile in Deformation of a Circular Plate Affected by Shock Pressure II. |
Tatsuya Nakauchi, Keisuke Tamaru, Hirofumi Iyama, Akio Kira & Masahiro
Fujita |
| 630 |
Collapse of Prismatic Hollow Cylinder in Axial Impact |
Minoru Yamashita, Manabu Gotoh, Yoshitaka Tange & Toshio Hattori |
| 631 |
New Impact Testing Method for Thin Sheet Metals Using Principle of SHPB Method. |
Naohiro Kimura, Yutaka Imaida & Tadashi Hasebe |
| 632 |
Bauschinger Effect of BCC Metals under Impact Loading |
Nobuyuki Tanaka, Tadashi Hasebe & Yutaka Imaida |
| 633 |
Impact Energy Absorption Characteristics of Cup-Shaped Environmental-Friendly FRP |
Kazuhiro Mizukami, Yutaka Imaida, Tadashi Hasebe, Yasunori Nakamura &
Tsutao Katayama |
| Bonding |
| 634 |
Formability of Aluminum / Steel Hybrid Sheets Prepared by Friction Stir Welding |
Takashi Iizuka, Yasuo Asida, Norio Takakura, Katsuhiko Yamaguchi, Keisei
Ni & Masaharu Iwamoto |
| 635 |
Improvement of Weld Strength of Al/Steel T-shape Joint by Welding Pressure Control |
Takashi Iizuka, Jiro Urita, Norio Takakura & Katsuhiko Ymaguchi |
| 636 |
Finite Element Analysis Application on Gap Control Mechanism in Batting Process of Tailored Blank Sheets Production (No.2 Determination of Design Parameters) |
Kousuke Terada, Susumu Takahashi & Hiroaki Uchijima |
| 637 |
Roll Joining of thin plates (2nd report) |
Hiromu Yamaki, Yukio Kasuga & Yukio Sanomura |
| Intarnationaru Session: Simulation of Sheet Metal Forming |
| 701T |
Analysis of the Effects of Yield Strength and Thickness Deviation on the Spring Back Property of Roll Forming Process 3-piece Can Body |
Kee -Cheol Park & Jai -Ik Kimだぶり |
| 702T |
Simulation of Tensile Test by Node Separation Method |
Kazutake Komori |
| 703T |
Effect of Force Correction Algorithm Arising from Change of Tool Normal on Sheet Forming Simulation Accuracy |
Hama Takayuki, Asakawa Motoo, Takamura Masato, Makinouchi Akitake &
Cristian Teodosiu |
| 704T |
Elasto-plastic Explicit Finite Element Analysis of Industrial Sheet Metal Forming Process With Adaptive Refinement Scheme Considering Thickness Stress for Shell Elements |
Jin -Woo Cho & Dong -Yol Yang |
| 705T |
Development of Dynamic Explicit Crystallographic Homogenization Finite Element Analysis Code to Assess Sheet Metal Formability |
Nguyen Ngoc TAM, Kenji Okada, Takehiro Hagisato, Tomiso Ohata, Eiji Nakamachi
& Yasunori Nakamura |
| 706T |
A Study of The Springback of High-Strength TRIP Steel |
Young Hwan Kim, Tae -Woo Kim, Young -Seon Lee & Jung -Hwan Lee |
| 707T |
Relationship between Forming Limit Diagrams of High-Strength Steel Sheets and Ductile Fracture Criteria |
Hirohiko Takuda, Tomofumi Kanie, Eiji Isogai & Tohru Yoshida |
| 708T |
Study on Sheet Forging (2nd Report: 3D-FEM Simulation of Flanging) |
Masao Murakawa, Masahiko Jin, Sawwakohn Typayaosoth & Sutasn Thipprakmas |
| 709T |
FEM Simulation Of Multi-point Elasto-forming |
Jong -Woo Park, Dong -Ha Kang & Tae -Won Kim |
| 710T |
Optimal Trimming Line Design for Flanging Using One Step FEM |
Wanjin Chung, Hyunbo Shim, Choondal Park & Sewook Oh |
| 711T |
FEM Simulation of Micro-Bending of Foils by Spark Forming |
Masaaki Otsu |
| 712T |
Simulation and Experiment of Resistance Heating of High Strength Steel Sheet Blank for Hot Press Forming |
Seijiro Maki, Yuuki Tanaka, Ken-ichiro Mori & Koji Miyoshi |
| 713T |
Finite Element Simulation of One-piece Press Forming of Automobile Steel Wheels without Welding |
Yohei Abe, Ken-ichiro Mori & Seijiro Maki |
| 714T |
Finite Element Simulation of Joining Process of Aluminum Sheets Using Self Piercing Rivet |
Ken-ichiro Mori, Toru Kato, Yohei Abe & Xean Wu |
| Special Theme Session: Technology of super fine grain materials to be created by rolling and metal working |
| 715T |
Development of the Microstructure Prediction Model during and after Large Reduction Forging |
Masaru Miyake, Takashi Kuroki & Yasuhiro Sodani |
| 716T |
Development of Super Short Interval Multi-pass Rolling Technology for Ultra Fine Grained Steel |
Tamotsu Sasaki, Suguhiro Fukushima, Manabu Etou, Youichi Haraguchi, Takashi
Shibahara, Kaori Kouno & Masayuki Wakita |
| 717T |
Microstructure Evolution in Plain Carbon Steel in Multi-Bending Process after Hot Rolling |
Naoki Nakata, Yukihiro Matsubara & Toshiki Hiruta |
| 718T |
Design of ultrafine grain structure through dynamic recrystallization for Type 304 stainless steel |
Tadanobu Inoue & Kotobu Nagai |
| 719T |
Fabrication of Ultrafine Grained Steels with Both High Strength and Adequate Ductility by Martensite Method |
Rintaro Ueji, Nobuhiro Tsuji & Yoritoshi Minamino |
| 720T |
Improvement of Mechanical Properties of Micro-screws Subjected Repetitive Side Extrusion |
Akira Azushima, Koshiro Aoki & Hiroyuki Hattori |
| 721T |
Grain Refinement and Mechanism of Copper Single Crystal Deformed by Equal Channel Angular Pressing |
Jiro Fushimi, Hiroyuki Miyamoto, Takuro Mimaki, Takashi Hashimoto &
Alexei Vinogradov |
| 722T |
Tensile Properties of ECAP Processed Copper Material |
Masafumi Hayaya, Tadashi Hasebe & Yutaka Imaida |
| 723T |
Influence of the Compressive Torsion Processing Conditions on Grain Refinement of Aluminum Alloy |
Yuji Kume, Makoto Kobashi & Naoyuki Kanetake |
| 724T |
Microstructural Control in Al-alloy by Shear Deformation in Rotation Using High Pressure Tosion Process |
Genki Sakai, Yuichi Miyahara, Neishi Kouji, Katsuaki Nakamura & Horita
Zenji |
| 725T |
Fabrication of Ultrafine Grained or Nanostructured Bulk Materials by ARB Process |
Tsuji Nobuhiroだぶり |
| 726T |
State of the Straining and Microstructure of Aluminum deformed by Torsion Extrusion. |
Mizunuma Susumu |
| 727T |
Development and Application of SVSP (Severe Vibration Straining Process) for Grain Refinement of Low Carbon Steel in Plate Form |
Hidehito Ohta, Yuichi Miyahara, Kouji Neishi, Katsuaki Nakamura, Kenji
Kaneko, Zenji Horita & Michihiko Nakagaki |
| 728T |
Control of Micro Structure for 6061 Alloy Using Severe Torsion Strain Process |
Katsunori Ohshima, Yuichi Miyahara, Koji Neishi, Katsuaki Nakamura, Kenji
Kaneko, Michihiko Nakagaki & Zenji Horita |
| 729T |
The Refinement Analysis of a Al-Mg Alloy and The Improvement of Mechanical Properties by Severe Torsion Straining Process |
Akihiko Higashino, Yuuiti Miyahara, Kouzi Neishi, Katuaki Nakamura, Kenzi
Kaneko, Mitihiko Nakagaki & Zenzi Horita |
| 730T |
Microstructural control of Magnesium Alloys by Severe Torsion Straining Process |
Naoki Emi, Yuichi Miyahara, Koji Neishi, Katsuaki Nakamura, Kenji Kaneko,
Michihiko Nakagaki & Zenji Horita |
| Roll formig, Shape correction |
| 731 |
Analysis of Roller Leveling Straightening of Bar and Wire by Elasto-plastic FEM |
Shinnosuke Irisawa, Motoo Asakawa, Shigeyuki Aizawa & Takayuki Hama |
| 732 |
Straightness on Roller Leveling of Bar and Wire |
Aizawa Shigeyuki, Asakawa Motoo, Irisawa Shinnosuke, Amari Masahiko &
Matuura Tomiyasu |
| 733 |
Roll Forming For Section With Bend Corner |
Hiroshi Ona |
| Material improvement |
| 734 |
Influence of Pulse Shape in Laser Gas Nitriding of Pure Titanium |
Edson Costa Santos, Masanori Morita, Kozo Osakada, Masanori Shiomi &
Masaya Takahashi |
| 735 |
Burnising of Internal Surface for Ductile Metals. |
Kinji Sato, Yoshiaki Sawa, Hotsumi Kagawa & Hisako Tsunekawa |
| 736 |
Improvement of Surface Properties of Material by Micro-shot Peening |
Yasunori Harada, Hideto Uesugi, Ken-ichiro Mori & Mitsugi Umemura |
| 737 |
Surface Improvement of Aluminum Alloy Bar by Protrusion Die |
Taro Muraoka, Motoo Asakawa, Satoshi Shindou, Tomoya Hayakawa & Shinji
Teruda |
| 738 |
Effect of Additional Shear Strain Layer on Strength and Ductility of Fine Drawn Wire |
Satoshi Kajino & Motoo Asakawa |