| The Proceedings of the
59th Japanese Joint Conference for Technology of Plasticity |
| Theme Session:Joining and Complex Technologies for Highten the Added Value | ||
|
101T |
Rectangular Mechanical Clinching of Aluminium Alloy Sheets | Yohei Abe,Toru Kato & Ken-ichiro Mori |
|
102T |
Influence of lubrication condition on joining road and peel strength of mechanical clinching. | Mizushima Daisuke,Murakami Hiroya & Andou Sachio |
|
103T |
Research on Plastic Flow Joining Method of Hard Disk-like Part and Hard Shaft (2nd Report) | Hiroya Murakami,Shoichiro Nishikawa & Hisanobu Kanamaru |
|
104T |
Development of Strong Flow-joining Method (8th Report) | Yasuyuki Okochi,Kazuhiko Kitamura,Kenji Hirota,Kei-ichi Matsunaga & Yoshihiko Ukai |
|
105T |
Development of Strong Flow-joining Method (9th Report) | Kenji Hirota,Taiki Sato,Yusuke Takata,Kazuhiko Kitamura,Yoshihiko Ukai & Keiichi Matsunaga |
|
106T |
Development of Strong Flow-joining Method (10th Report) | Kenji Hirota,Taiki Sato,Kazuhiko Kitamura,Yoshihiko Ukai & Keiichi Matsunaga |
|
107T |
Mechanical Properties of Tough Pitch Copper to Brass Joint by Friction Spot Welding | Yoshimitsu kano & Katoh Kazuyoshi |
|
108T |
Mechanical properties of rolled sheet by friction surfacing for improvement of corosion resistance of 7075 aluminum alloy | Dai Nakama & Kazuyoshi Katoh |
|
109T |
Mechanical properties of friction surfaced AZ31/AZX311 magnesium alloys | Kiyohide wada,Dai nakama,Kazuyoshi Katoh & Tutomu murai |
|
110T |
Mechanical properties of 6061 aluminum alloy joint by under water friction seam welded. | Chihiro Mizuta & Kazuyoshi kato |
|
111T |
Fundamental Study on Formability of Laser Butt Welded Mild Steel/Aluminum Hybrid Sheet | Takashi Iizuka,Ryo Ohnishi & Norio Takakura |
|
112T |
Improvement of Drawability of Fe Shape-Memory Alloy Wire | Kazunari Yoshida & Takanori Sato |
|
113T |
Ultrasonic Welding of Anodized Aluminum and Plastics Using Inserts. | Tomoaki Ishikuro,Shin-ichi Matsuoka & Shigeki Kakiuchi |
|
Micro Forming | ||
|
114 |
Evaluation of anisotropy of micro/meso-scale plastic deformation using heading test | Takehiko Makino,Kuniaki Dohda,Akihiro Ishitani & Hualing Zhang |
|
115 |
Effect of die surface on micro-pin rotary forming | Kuniaki Dohda,Takehiko Makino,Hualing Zhang & Yoshio Nonaka |
|
116 |
Development of giant-magnetostriction-drive micro press | Kuniaki Dohda,Takehiko Makino,Hidehito Ichiki & Ken-ichi Kasahara |
|
117 |
FE Modeling for Roughness Evolution on Free Surface of Sheet Metal Using Microscopical Inhomogeneity Evaluation by Statistical Distribution of Hardness. | Tsuyoshi Furusima,Kouji Nakata,Ken-ichi Manabe & Sergei Aleksandrov |
|
118 |
Effect of Microscopical Inhomogeneity of Material on Macroscopic Deformation Behavior | Tsuyoshi Furushima,Ken-ichi Manabe & Sergei Aleksandrov |
|
119 |
Effect of Surface Properties of Aluminum Alloy Foils on Micro Deep Drawability | Tetsuhide Shimizu,Masahiro Ogawa,Ming Yang & Ken-ichi Manabe |
|
120 |
Laser Dieless Drawing of Micro Metal Tube | Tsuyoshi Furushima,Yuta Noda & Ken-ichi Manabe |
|
Theme Session:Practical Use of Dry Press
Forming | ||
|
201T |
Development of hybrid DLC coatings toward dry stamping | Tatsuhiko Aizawa |
|
202T |
Formation and Properties of DLC Films for Press Forming Die | Kazuo Morikawa,Sadao Takeuchi & Katsuyuki Fujimura |
|
203T |
Dry Cutting of various materials with DLC coated tool | Hiroyuki Noguchi,Masako Higaki,Tutomu Toyooka,Susumu Takahashi,Masao Murakawa & Tooru Shimizu |
|
204T |
Deveropement of DRY Deep Drawing with use
of DLC corting Die |
Masako Higaki,Hiroyuki Noguti,Titomu Toyooka,Susumu Takahasi & Masao Murakawa |
|
205T |
Longevity evaluation of dry ironing with use of DLC coating tool | Katsuyuki Fujimura,Masayoshi Muraki,Seiji Kataoka,Masako Higaki,Hiroyuki Noguchi & Susumu Takahashi |
|
206T |
Nanostructure and mechanical characterization of nano-columnar coatings for dry micro-stamping | Tatsuhiko Aizawa,Eiji Iwamura & Takuhiko Uematsu |
|
207T |
Comparison of mono-layered and nano-laminated DLC coated punches on the beding and ironing step in dry micro-stamping | Tatsuhiko Aizawa,Eiji Iwamura & Kuniyoshi Itoh |
|
208T |
Effects of Ultrasonic Energy on Press Fitting Process of Metals | Takashi Sato,Tsuyoshi Yokosawa & Seiji Kataoka |
|
209T |
Developments and Characteristics of New Ceramics for Light Load Shearing and Forming Process | Kouki Minamoto,Kota Tsutsumi,Kenji Tamaoki,Seiji Kataoka & Mituyosi Nagano |
|
210T |
Draeing and ironing of SPCC steel uisng electricall conndactive ceramics dies | Toru Shimizu,Susumu Takahashi,Kouki Minamoto,Kenji Tamaoki & Seiji Kataoka |
|
211T |
Drawing of SUS304 stainless steel uisng electricall conndactive ceramics dies | Tsutomu Toyooka,Toru Shimizu,Kouki Minamoto & Seiji Kataoka |
|
212T |
Practical Use of Dry Shearing Using Ceramic Tools | Kenji Tamaoki,Seiji Kataoka,Kouki Minamoto,Hatsuo Aragane & Takunori Kyuno |
|
213T |
Development of diamond coating system for press forming die. | Sadao Takeuchi,Tadao Kato & Katsuyuki Fujimura |
|
214T |
Dry Blanking on SUS304 with use of Diamond Coated Tool | Seiji Kataoka,Kenji Tamaoki,Tadao Kato,Kazutaka Kanda,Shigeto Takano & Takunori Kyuno |
|
215T |
Dry Deep Drawing on SUS304 With use of Diamond Coated Tool | Seiji Kataoka,Kenji Tamaoki,Tadao Kato,Kazutaka Kanda,Shigeto Takano & Takunori Kyuno |
|
216T |
Polishing method of CVD diamond film coated on curved surface -Development of poloshing device- | Tsuyoshi Yokosawa,Seiji Kataoka,Takashi Satou & Yoshikazu Teranishi |
|
Sheet Metal Press
Forming | ||
|
217 |
Prediction of stress-strain curve of metal sheet by Erichsen cupping test | Morikawa Yuichi,Koyama Junichi,Jin Ying Jun,Ogata Atushi,Murata Makoto & Kuboki Takashi |
|
218 |
Intelligent Process Control of Circular-Cup Deep-Drawing Using Local Heating and Cooling Technique | Ken-ichi Manabe & Xiaogang Fang |
|
219 |
Study on Strain Rate Dependency in High Strength Steel of Dual Phase Type under Compressive Pre-strain | Yutaka Imaida,Tatsuya Tanaka,Shintaro Yoshihara & Keiko Natori |
|
220 |
Biaxial-Stressed Forming Limit of Sheet Metal Laminate Consisting of Perforated Core Sheet and Thin Skin Sheets | Masato Nakamura,Ryutarou Hino & Fusahito Yoshida |
|
221 |
Efect of anisotropic yield functions for springback analysis of aluminum alloy sheets | Satohi Suikawa,Shohei Tamura,Kohei Ogawa,Hiroshi Hamasaki,Takeshi Uemori,Tetsuo Naka & Fusahito Yoshida |
|
222 |
Study on spring back for rear member
model -Experimental results of press forming and analysis of spring back mechanizm- |
Tohru Yoshida,Koichi Sato,Eiji Isogai,Koji Hashimoto,Yukihisa Kuriyama,Koichi Ito & Gen Uemura |
|
223 |
Study on spring back of rear member
model -Spring back analysis by using kinematic hardening model- |
Eiji Isogai,Tohru Yoshida,Koichi Sato,Koji Hashimoto & Yukihisa Kuriyama |
|
224 |
Study on spring back for rear member
model -Investigation of countermeasure for spring back- |
Koichi Sato,Eiji Isogai,Tohru Yoshida,Koji Hashimoto & Yukihisa Kuriyama |
|
225 |
In-Plane Reverse Loading Test of Stainless Steel Sheet for Electronic Parts | Rena Saito,Toshihiko Kuwabara,Takaaki Hirano & Nobuaki Ohashi |
|
226 |
Biaxial Tensile Test and Material Modeling of Ultra-thin Stainless Steel Sheet | Toshihiko Kuwabara & Satoko Murakoso |
|
227 |
Forming Limit of Stretch Flanging with Connection of Lines and Arcs | Yuichiro Kurosawa,Motoo Asakawa,Ikuhiko Hayashi,Jiro Iwaya,Takayuki Yamano,Hiroshi Akamizu & Masashi Sakata |
|
228 |
Influence of Sheared Surface Properties of Sheet Materials and Steel Grade on Bore Expanding Limit | Yasuhiro Ishihara,Yoshinori Yoshida,Nobuki Yukawa & Takashi Ishikawa |
|
Composite Materials | ||
|
301 |
Molding Technology of CFRP Using UV Curable Resin | Minami Kimura & Kazuma Yoshitomi |
|
302 |
Separation and Recycling of Abandoned Carbon
Fiber |
Minami Kimura & Toru Tuchida |
|
303 |
Trimming of CFRP Seat | Minami Kimura & Yuta Kakubo |
|
Incremental Forming | ||
|
304 |
Incremental Forming of Perforated Plates | Kimiyoshi Kitazawa & Hiroki Takano |
|
305 |
Incremental Forming of Tailored Blanks | Kimiyoshi Kitazawa & Hiroki Takano |
|
306 |
Deep Drawability of 5052 Aluminum Alloy Sheet Flattened by Incremental Forming | Hiroki Takano & Kimiyoshi Kitazawa |
|
307 |
Effect of CO2 Emission Reduction on Cold Recycling Process of Sheet Metal Waste | Hiroki Takano & Kimiyoshi Kitazawa |
|
308 |
Analysis of Strain Distribution on Incremental Forming of Sheet Metal Using Bar Tool | Nobuyuki Suzuki,Toshiyuki Sano & Kentaro Takashina |
|
309 |
Strain Distribution of Cylindrical Cup with Flange Using Two-stage Incremental Forming | Hideo Iseki |
|
310 |
Laser assisted incremental sheet metal forming of titanium denture plate (Reduction of forming load) | Shigekazu Tanaka,Tamotsu Nakamura,Kunio Hayakawa,HideoNakamura & Kazuo Motromura |
|
311 |
Sheet Metal Bending by Laser Peen Forming with Femtosecond Laser | Yoshihiro Sagisaka |
|
312 |
Effect of local heating on residual stress and shape fixability in incremental sheet forming with local heating | Naoaki Nagaishi,Yuki Yamamoto,Ryutaro Hino,Tetsuo Naka & Fusahito Yoshida |
|
Tube Forming | ||
|
313 |
Effect of thickness on Cross-sectional Deformation in Circular Tube by Pure Bending | Kazuhito Takahashi,Ryosuke Muta,Takashi Kuboki & Makoto Murata |
|
314 |
Development of Pipe Bending by Local Bulging | Shuhei Yamagata,Satoru Kikunaga,Takashi Iizuka & Norio Takakura |
|
315 |
Development of Intrusion Bending for Elbow Pipes | Koji Yamane,Hisashi Naoi,Kunihiro Yabuki,Masahiro Asai & Munekatsu Hurugen |
|
316 |
Warm T-joint Hydroforming of AZ31 Magnesium Alloy Tube | Ken-ichi Manabe,Kota Fujita & Kazuo Tada |
|
317 |
Effect of Lubrication on Deformation Behavior of Tube in Hydraulic Bulging with Square Die (5th Report) | Atsushi Shirayori,Ryoichi Hirayama,Michiharu Narazaki & Sadakatsu Fuchizawa |
|
318 |
Effect of Cross-sectional Shape of Tube on Fixation of Flange by Tube Bulging | Kousuke Morioka,Hidenori Yoshimura,Yutaka Mihara & Masahiro Miyazaki |
|
319 |
A Study of Axial Compression for Aluminum Pipes with Internal Pressure | Masayasu Yoshida,Hisashi Naoi,Shota Ide & Shouzi Yamazaki |
|
320 |
Effect of Expanding Length on Hydroforming Deformation in Width Direction with Axial Feeding | Masaaki Mizumura,Koichi Sato & Yukihisa Kuriyama |
|
321 |
Expanding Deformation of Bent Portion of Tube during Hydroforming after Draw-bending(Effects of Outside and Inside Eccentric Expansion) | Naoyoshi Sakaguchi,Katsushi Ishigaki,Naoto Kaneda & Masayasu Kojima |
|
322 |
Controlling Technology of Longitudinal Curvature in Rib Forming for Structural Channel | Takahiro Makiyama,Toshiya Teramae,Keii Ueno,Atsushi Kanno & Katsuhiro Shimada |
|
323 |
Effect of tube thickness on nosing process with relieved die | Kominami Atsushi,Murata Makoto & Kuboki Takashi |
|
324 |
Tensile Deformation of Resistance Heated Aluminium Alloy Tube | Atsushi Shirayori,Susumu Okazaki & Michiharu Narazaki |
|
325 |
Research of Ferrous Shape Memory Alloy Pipe Joints for Buried Piping for Cables of Electricity | Hideaki Yamamoto,Hisasi Naoi,Hideki Okada & Takasi Kurita |
|
326 |
Forming behavior in the part processed by the diameter-enlargement working method for hollow shafts | Tomoyuki Okita,Nagatoshi Okabe,Yoshitaka Kuwahara,Xia Zhu & Keiji Ogi |
|
327 |
Formability of a diameter-enlargement part outline-restrained by dice | Kanau Takahashi,Nagatoshi Okabe,Yoshitaka Kuwahara,Xia Zhu & Keiji Ogi |
|
Joining | ||
|
328 |
Mechanical Fastening of CFRP (Ⅱ) | Minami Kimura & Masashi Sekine |
|
329 |
Mechanism of ultrasonic welding | Shin-ichi Matsuoka & Junko Maeno |
|
330 |
Cold Butt Joining of Light Metal Sheet by Shot Peening | Yasunori Harada & Yuji Kobayashi |
|
331 |
An Experimental Study on Strain Rate Sensitivity of Deformation Behavior in the Thermosetting and the CTBN Modified Epoxy Adhesives | Takeshi Iwamoto,Toshimasa Nagai,Toshiyuki Sawa,Hideaki Kuramoto & Norio Uesugi |
|
332 |
Joining of A Shaft with A Disk Using Polymer Elements (2nd Report) -Rotational Strength and disassembly- | Kasuga Yukio,Kumai Takanori,Kawamori Shigehiro & Okai Toshihiko |
|
333 |
Influence of Shield Gas Addition on Weld Ability of Steel/ Aluminum Alloy by Pressurizing Butt Laser Joint | Takashi Iizuka,Takehiro Saitoh & Norio Takakura |
|
334 |
Influence of Coil Width and Thickness on Seam Welding by Applying Magnetic Pressure | Keigo OkagawaTomokatsu Aizawa,Mitsuji Hirohashi & Masaki Ishibashi |
|
335 |
Spot Welding of Copper Foils on Flexible Printed Circuit by Applying Magnetic Pressure | Tomokatsu Aizawa,Keigo Okagawa,Yoshitaka Sugiyama & Kenichi Hanasaki |
|
Roll Forming | ||
|
336 |
Taper Shape Forming by Flexible Roll Bending System | Hideo Koyama & Satoshi Matsuzaki |
|
337 |
Development of Servo Cold Roll Forming Machine | Hiroshi Ona,Ishou Rihou,Takuo Nagamachi & Kiyomasa Hoshi |
|
338 |
Effect of Roll Conditions on Corner Shape of Square Steel Pipe (6th Report) | Takuo Nagamachi,Takehumi Nakako & Daisuke Nakamura |
|
Surface Treatment | ||
|
401 |
Laser-assisted aerosol deposition process of ultra fine particles | Kato Kyouhei,Tanaka Sigekazu,Nakamura Tamotsu & Hayakawa Kunio |
|
402 |
Effect of Shot Peening on Surface Characteristics of carbon steel | Yasunori Harada,Ryota Yakura & Kenzo Fukaura |
|
403 |
Evaluation of tribocharacteristics of thin hard coatings against Mg | Hideaki Katoh,Kuniaki Dohda,Takehiko Makino & Teruaki Nozawa |
|
404 |
Effect of CrN interlayer on tribocharacteristics in ironing process | Kuniaki Dohda,Takehiko Makino & Yasuhiro Hayashida |
|
High Energy Rate
Forming | ||
|
405 |
Method Used for Catching the Reactive Material in Extremely High Impulsive Pressure Generator | Akio Kira,Takuya Hirota,Kazuyuki Hokamoto,Yasuhiro Ujimoto & Masahiro Fujita |
|
406 |
Flight of the Metal Plate accelerated by the Pressure of Detonation Gas | Akio Kira,Keiichi Yamoto,Hideharu Iwasaki,Moto Shirahase & Masahiro Fujita |
|
407 |
An Investigation on the Plastic Deformation
Behavior of a Circular Metal Plate under Impulsive Pressure Loading |
Hirofumi Iyama,Yasuo Ishigori,Minoru Mochihara & Masahiro Fujita |
|
408 |
Effect of Inertial Force on Formation of First Plastic Buckling Lobe in Impact of Tubular Struscture | Yamashita Minoru,Okuyama Tomohito,Hattori Toshio & Nishimura Naoya |
|
Wood Forming | ||
|
409 |
An examination of ejection property from a nozzle in the injection molding of the bamboo powder | Keisuke Yamaishi,Takashi Iizuka,Mitani Masami,Tunehisa Miki & Norio Takakura |
|
410 |
Hotpressing of Wood Using Airtight Mold | Tsuyoshi Ohata,Masashi Narita,Satoru Kikunaga,Nobuo Hatanaka,Takashi Iizuka & Norio Takakura |
|
411 |
Influence of Buckling and Flaking in
Compressing on Strength of Die-forged Product |
Takasi Iizuka,Sho Okada,Keisuke Yamaisi,Nobuo Hatanaka & Norio Takakura |
|
412 |
Transparency Process of Compressed Wood | Kimiyoshi Kitazawa & Hiroki Takano |
|
413 |
Permanent Shape Fixation Phenomenon of Large Compressed Wood | Wataru Okajima,Kimiyoshi Kitazawa & Hiroki Takano |
|
Theme Session:Macroscopic and Microscopic
Deformation Behavior of Rolled Material in Roll
Bite | ||
|
414T |
Application of Rolling Theory with Noncircular Roll Flattening to Dry Temper Rolling of Tinplates | Hiromi Matsumoto |
|
415T |
Analysis of longitudinal buckle in temper rolling | Kazutake Komori |
|
416T |
Deformation behavior analysis by ALE method on 3-roll type ring rolling. | Morihiko Nakasaki,Ichiro Takasu,Toshifusa Nakamizo & Hiroshi Utsunomiya |
|
417T |
Influence of surface construction on roll diameter and rolling velocity. | Matsuo Ataka,Minoru Miura & Kousuke Watanuki |
|
418T |
Shear deformation introduced by asymmetric rolling | Takaya Ueno,Hiroshi Utsunomiya & Tetsuo Sakai |
|
419T |
Observation of Scale Behaviour during Hot Rolling by Oxide Glass | Shoichi Doi,Ken-ichiro Hara,Hiroshi Utsunomiya,Tetsuo Sakai & Shusuke Yanagi |
|
420T |
Effect of surface projection on cross-sectional profile of rolled strip after cold rolling | Tsuyoshi Hashizume & Jun Yanagimoto |
|
421T |
Deformation behavior of the strip with a surface projection during cold rolling | Jun Yanagimot & Tsuyoshi Hashizume |
|
Rolling | ||
|
422 |
Temperature Analysis of Reverse Strip Rolling of Difficult Material to Process | Tadatsugu Yoshida |
|
423 |
Tandem Rolling Analysis of Non Driving Roll | Tadatsugu Yoshida |
|
424 |
Formation of randum orientation in AZ31 magnesium alloy sheet by rolling and high-temperature annealing | Kenji Kii,Masahide Kohzu,Hiroyuki Nishio,Masato Tsujikawa,Kenji Higashi & Hirofumi Inoue |
|
425 |
Texture and Formability of Roll-Bonded AZ31Mg/Ti and AZ61Mg/Ti Clad Sheets | Hirofumi Inoue,Seiji Mizutani,Kunihiko Nakamura & Takayuki Takasugi |
|
426 |
Flatness control system for a prototype mill of NSC intelligent mill | Shigeru Ogawa,Kenji Yamada,Toshiyuki Shiraishi & Yasuhiro Higashida |
|
427 |
Flatness controllability at very low reduction in a prototype mill of NSC Intelligent Mill | Kenji Yamada,Shigeru Ogawa,Toshiyuki Shiraishi & Yasuhiro Higashida |
|
Material Property , Material
Testing | ||
|
428 |
Optimization of specimen geometry for
high-speed tensile testing based on elastic-bar type - Part II - - dependence on material property - |
Satoshi Hirose,Shunji Hiwatashi,Akihiro Uenishi & Hiroshi Yoshida |
|
429 |
Reconsideration on Standardization of Impact Compression Test at Constant Strain Rate by Split Hopkinson Pressure Bar Technique | Yasuhisa Sato & Minoru Yamashita |
|
430 |
Study of the Fracture Criteria for Low Ductile Materials | Kazuhiro Okauchi,Yutaka Mihara & Hidenori Yoshimura |
|
431 |
Influence of test piece countermeasure buckling in tensile and compression test (report No.2) | Ishikami Keisuke,Kuboki Takashi,Murata Makoto,Jin Yingjun,Omata Hitoshi & Yamaya Yasushi |
|
432 |
Effect of Deformation Behavior of MH spheres on Compressive Characteristics of Their Structure | Masafumi Horikawa,Yutaka Mihara,Kazunari Shinagawa & Hidenori Yoshimura |
|
433 |
New porous metal with high bending
strength - Tubular structure with string of Metallic Hollow Spheres - |
Tatsuya Ishikawa,Yutaka Mihara & Hidenori Yoshimura |
|
434 |
FEM simulation of laser forming process with line beam | Akihiro Mita,Shigekazu Tanaka,Yasushi Yamaya,Asami Morino & Hitoshi Omata |
|
435 |
Characteristic of steel plate after CO2 laser cutting | Li Ruotao,Jin YingJun,Junichi Koyama,Hiroaki Ishiguro,Makoto Murata & Takashi Kuboki |
|
436 |
Forecast of tensile stress of work by cold working | Hiroki Tsuruta,Takashi Kuboki & Makoto Murata |
|
437 |
Change in hardness statistics during annealing of cold-rolled aluminum sheet | Tsuyoshi Yukimoto,Hiroshi Utsunomiya & Tetsuo Sakai |
|
438 |
Thin - Film Forming with Titanium Fiber by Compression Shearing Method under Room Temperature | Noboru Nakayama,Masahiko Nakazawa,Hiroyuki Miki & Hiroyuku Takeishi |
|
439 |
Evaluation of Fatigue Properties for Small, Thin Die Parts | Isao Kuboki & Masaaki Ozawa |
|
Bending | ||
|
501 |
Formed Geometry and Interface of Layer-Integrated Steels after Hat-bending | Jun Yanagimoto,Tetsuo Oya,Nicolas Tiesler & Seiichiro Kawanishi |
|
502 |
Formed Geometry of Layer-Integrated Steels after Cold/Warm V-bending | Seiichiro Kawanishi,Tetsuo Oya,Nicolas Tiesler & Jun Yanagimoto |
|
503 |
Finite Element Analysis of Bending Deformation of the Layer-integrated Steel | Oya Tetsuo,Nicolas Tiesler,Kawanishi Seiichiro & Yanagimoto Jun |
|
504 |
The Scoring Condition of the Corrugated Cardboard and Bending Strength of Creased Line | Takamatsu Tomohiro,Nagasawa Shigeru & Fukuzawa Yasushi |
|
505 |
Method of Forming Pipes by Feed Bending of Titanium Sheets | Matsuo Ataka,Yasushi Ueno,Shuji Nakamura,Yu Fukazawa & Masanori Yamaguchi |
|
506 |
Effect of bending force on angle accuracy of bottoming | Takahiro Shibata,Yingjun Jin,Junichi koyama,Takashi Kuboki & Makoto Murata |
|
507 |
Effect of Punch Track on L-Bending of Sheet Metal | Yingjun Jin,Junyichi Koyama,Kazunari Imai,Takashi Kuboki & Makoto Murata |
|
508 |
Finite Element Analysis of 3 Point Bending of Spheroidal Graphite Cast iron by Taking Account of Difference in Tensile and Compressive Behaviors | Kunio Hayakawa,Ryo Nagaki,Tamotsu Nakamura & Shigekazu Tanaka |
|
509 |
Effect of twin formation by repetitive bending on texture of AZ61 magnesium alloy sheet | Yoshifuru Sunaga,Yoshinori Tanaka,Motoo Asakawa,Masahito Katoh & Masaru Kobayashi |
|
510 |
Research onto sheet V-bending | Wang zhrgang,Kanada nobuhiro & Ikeido shota |
|
511 |
Influence of Amount of Pre-strain on Plastic Deformation Behavior(Subsequent Plastic Deformation Behavior of Steel Sheet Pre-strained with Plane-strain Tension/Compressions) | Satoshi Shirakami,Eji Tsuru & Toshihiko Kuwabara |
|
512 |
Improvement in Accuracy of C-U-O Forming Pipe Made of High Strength Steel Sheet | Hideo Koyama & Ikumi Kajihara |
|
513 |
Effect of temperature on draw-bending process of magnesium alloy sheet | Takayuki Hama,Masaaki Itazu,Keisuke Ochi,Hitoshi Fujimoto & Hirohiko Takuda |
|
514 |
Experimental validation of draw-bending simulation using local interpolation for tool surfaces | Takayuki Hama,Eiji Isogai,Tohru Yoshida & Hirohiko Takuda |
|
515 |
Research of Bending Method Drawing by Wire Rope from Tapered Steel Tube | Takahiro Miyakawa,Xuefeng Zhu,Hisashi Naoi & Hideo Shiohara |
|
516 |
Trial Manufacture of Helical Springs by Ultrasonic-Vibration Coiling Method | Masahiko Jin,Shin-ich Nagakubo,Masami Abe & Tetsuo Oki |
|
517 |
Spring Back Evaluation of Ni-Cr Alloy Sheets with V Bending Test | Suzuki Keiji,Manabe Ken-ichi & Teranmae Toshiya |
|
Rotary Forming | ||
|
518 |
Taper Angle and Feed Speed Limitations on Circular Tube Spinning Forming | Shigefumi Kihara,Yuya Nakata,Hiroaki Mizumoto,Youichi Takahashi & Koji Higaki |
|
519 |
Feed Speed and Critical Length of Contract Diameter in Spinning Forming for Circular Tube | Shigefumi Kihara,Yuta Sumitomo,Hiroaki Mizumoto,Youichi Takahashi & Koji Higaki |
|
520 |
Influence of Surface Properties on Bioactivity in Form Rolled Ti Rod | Yoshinori Yoshida,Kensuke Kuroda,Ryoichi Ichino,Yoshio Nonaka,Naofumi Ogihara & Norishige Hayashi |
|
521 |
Finish Rolling Properties of Cr-Mo Sintered Steel Rollers Having Different Initial Densities | Teruie Takemasu,Toshinaka Shinbutsu,Takao Koide & Yoshinobu Takeda |
|
522 |
Development of Pinch Roll Type Incremental Forming Equipment | Hideo Koyama & Takuya Matsumura |
|
523 |
Improvement of Accuracy in Incremental Forming of Welded Pipe End | Hideo Koyama & Keita Nishimura |
|
524 |
Development of Bellows Processing Method of Minute Tube with Side Roll | Hideo Koyama & Takahiro Aoyagi |
|
525 |
Molding properties of thin wall tube at spin ironning process | Takahashi Naoto,Kuboki Takashi,Murta Makoto,Matsuda Kiyomasa & Sanda Kazuhiko |
|
Theme Session:4th INTERNATIONAL SESSION
2008 | ||
|
526T |
FEM Studies for Pipe Bending Process of Auto Chassis Component | Zhe-Hao Yin,Myoung-Su Chae,Kee-Dong Lee,Chun-Dal Park & Young-Suk Kim |
|
527T |
new manufacturing method for V-shaped tubular CTBA using hot forming | Yajing Zhang,Kee-June Mun,Tae-June Kim & Young-Suk Kim |
|
528T |
Inner-cup Ironing Test of Chloride-free forming oils for Stainless Steel | Masato Katsuragawa & Kazuhiko Kitamura |
|
529T |
Mechanical and Forming Characteristics of A High Strength Boron-alloyed Steel in Hot Press Forming | Myoung-Su Chae,Byung-Cheol Park & Young-Suk Kim |
|
530T |
Strain path dependency on ductile fracture limit curves of aluminum sheet in press forming | Moon-Kee Bae,Sang-Kwan Lee,Noh-Kwang Park & Young-Suk Kim |
|
531T |
An Experimental Study on Transformation Thermo-mechanical Behavior of TRIP Steel under Impact Loading | Takeshi Iwamoto,Mohammed Cherkaoui & Toshiyuki Sawa |
|
532T |
Forgeability and Plastic Anisotropy for Extruded Bar of AZ31B Magnesium Alloy | Motoki Terano,Ryo Matsumoto & Kazuhiko Kitamura |
|
533T |
Characterization of Shock Consolidated Mg-SiC Composites | Palavesamuthu Manikandan & Kazuyuki Hokamoto |
|
Powder Forming | ||
|
534 |
Effect of alloy compositions on high temperature strength of Al-Mn-Mg alloys prepared by powder metallurgy process | Yuuya Ohki,Yousuke Kubota & Makoto Sugamata |
|
535 |
Properties of pure aluminium containing bimodal structure produced by powder metallurgy | Masahiro Kubota,B. P. Wynne & Makoto Sugamata |
|
536 |
Influence of Input Heat on Semisolid Sinter-Forging Performance in Rapidly Resistance-Heated Hypereutectic Al-25wt%Si Alloy Powder Compact | Seijiro Maki,Masayuki Noda & Eitoku Nakanishi |
|
537 |
Micromechanics modeling of Sintering Stress and Viscosity for Nickel/Alumina Powder Mixtures | Kazunari Shinagwa |
|
538 |
Influence of Fabricate Conditions on Consolidation of Titanium Powder by Compression Revolution Shearing Method under Room Temperature | Yuji Masuda,Noboru Nakayama,Hiroyuki Miki & Hiroyuku Takeishi |
|
539 |
Influence of specimen height on aluminum machined chip consolidation by Compressive Torsion Processing | Takashi Takahashi,Yuuji Kume,Makoto Kobashi & Naoyuk Kanetake |
|
540 |
Visualization and Quantitative Analysis of Internal Deformation of Specimen Processed by Compressive Torsion Processing | Masakazu Motohashi,Yuji Kume,Makoto Kobashi & Naoyuki Kanetake |
|
541 |
Microstructure and mechanical property of magnesium alloy consolidated from chips by compressive torsion processing | Kazuteru Tsutsui,Yuji Kume,Makoto Kobashi & Naoyuki Kanetake |
|
542 |
Thermo-mechanical properties of TiNi shape memory alloy wires fabricated by powder metallurgy and plastic working | Kenichi Shintani,Takuya Osumi,Ryosuke Matsui,Hideki Kyogoku & Fusahito Yoshida |
|
543 |
Characteristics of machinable lead-free P/M brass alloys with dispersed graphite | Hisashi Imai,Katsuyoshi Kondoh,Yoshiharu Kosaka & Akimichi Kojima |
|
544 |
Microstructures and mechanical properties of powder metallurgy extruded magnesium alloy via rapid solidification | Katsuyoshi Kondoh,El-Sayed Ayman Hamada,Masashi Kawakami & Hisashi Imai |
|
545 |
Effect of Alumina Content and Alumina Particle Diameter on Mechanical Properties of Alumina Dispersion Strengthened Magnesium | Noriyuki Onuma,Sigehiro Kawamori,Yukio Kasuga & Tosihiko Okai |
|
Extrusion | ||
|
601 |
Net Shape Forging of Magnesium Alloy Spiral Parts | Kenji Nakanishi,Yuji Mure,Takehiko Matsuda,Satoru Kuwaharada & Manabu Maeda |
|
602 |
Effect of Friction on the Metal Flow Condition and Work-harden Subsurface Zone in Cu and Cu alloy | Shunpei Kamitani,Kenji Nakanishi,Akito Yoshidome & Tomohiro Tsuzuki |
|
603 |
Measurement of Sliding Friction on Plane tool in Plane Strain Extrusion Test | Shunpei Kamitani,Kenji Nakanishi & Takahumi Matsushita |
|
604 |
Influence of Dies Angle and Exit Position on Curved Rectangular Extrusion Processing of Resin Material. | Shigefumi Kihara,Daisuke Toyota,Mitsunobu Shiraishi & Makoto Niikawa |
|
605 |
Influence of die shape on torsion extrudion characteristics of Mg alloy | Ryou Fujise,Yasurou Miyazaki,Susumu Mizunuma,Hajime Takahasi,Kazuhiro Mitsui & Masahide Kohzu |
|
606 |
A Study on New Extrusion of Fuel Cell Separator with Orthogonal Channel（6th report）- Influence of Inflow Condition in Materials Supply Method from the Side of Channel in Product - | K.suzuki,H.hoshino & Y.uchida |
|
607 |
Research of Deformation in Extrusion of Billet with Double Layer | Gen Murata & Michihiko Hoshino |
|
608 |
Grain refining for magnesium alloy by excentric torsion extrusion with rapidly-rotation (2nd report) | Masahide Kohzu,Yuki Nagata,Masato Tujikawa,Hajime Takahashi & Susumu Mizunuma |
|
609 |
Influence of Friction Conditions on Torsion Extrusion Forming Process | Norio Takatsuji,Yuichi Kaimi,Keiichi Tanppa,Toshihiro Takai,Tetsuo Aida & kazuo Murotani |
|
610 |
The Extrusion of Compaction Molding billets Used of Magnesium Alloy Chips | Shin-ichi Matsuoka,Tomohiko Goshima,Tsutomu Murai & Fumiaki Nakagawa |
|
611 |
Shaping of Helical Gear by Cold Extrusion through Expansion of Inner Diameter of Workpiece | Hajime Yoshida,Yoshihisa Sakaida,Tamotu Nakamura,Kunio Hayakawa,Kei Takahashi & Yozo awaki |
|
612 |
Effect of Tube Thickness on Joining of Aluminum Tube and Holed Rib by Extrusion | Moroi Tsutomu,Kuboki Takashi & Murata Makoto |
|
613 |
Semisolid Extrusion of Aluminum Alloy Machining Scrap－4 | Tadahisa Mera,Sumio Sugiyama & Jun Yanagimoto |
|
614 |
Microstructures and Mechanical Properties of Extruded Magnesium Alloy Using Dispersed Ti in Composite Mg | Masashi Kawakami,Katsuyoshi Kondoh & Hisashi Imai |
|
615 |
Extrusion Process for Producing the Hollow Shaft with Helical Tooth in the Outside/Inside | Makoto Nikawa & Mitsunobu Shiraishi |
|
Shearing | ||
|
616 |
Influence of Pre-Punched Hole on Shearing Characteristics | Takashi Nakamura,Masahiro Sasada & Isamu Aoki |
|
617 |
Influence of Materials Supporting Conditions on Clearance Compensation Effect in Fine Precision Shearing (2nd Report) | Takuya Sakurai,Masahiro Sasada & Isamu Aoki |
|
618 |
Analysis for Fine-Blanking Process of High-Tensile Steel using FEM- Influence of V-ring Indenter on Sheared process- | Toru Tanaka,Shuhei Yoshimura,Yuichi Tadano,Seiya Hagihara & Takanobu Mori |
|
619 |
Analysis for Fine Blanking Process Using FEM
Taking Account of Ductile Fracture |
Takaki Ogawa,Toru Tanaka,Syuhei Yoshimura,Yuichi Tadano & Seiya Hagihara |
|
620 |
Piercing Characteristics of High Tensile Strength Steel Sheet in Super Cooled Austenitic State | Seijiro Maki,Takashi Hattori & Eitoku Nakanishi |
|
621 |
Shear Characteristic of Ultra Fine Grain Steel (3rd Report) | Shiro Torizuka,Takafumi Komatsu,Shinichi Nagayama & Eijiro Muramatsu |
|
622 |
Shear Characteristic of Ultra Fine Grain Steel (4th Report) | Shiro Torizuka,Takafumi Komatsu,Shinichi Nagayama & Eijiro Muramatsu |
|
623 |
Effect of Thickness by New Shearing Method for Steel Sheet Metal | Akinori Tanaka,Makoto Murata,Takashi Kuboki & YingJun Jin |
|
624 |
Characteristics of the Small Clearance Piercing of High Strength Steel Plate by Right Angle Punch | Hiroya Murakami,Nao Miyatake,Nobuyuki Kasahara,Takaaki Imura & Takao Ito |
|
625 |
Characteristics of the Small Clearance Piercing of High Strength Steel Plate by PW Punch | Hiroya Murakami,Nao Miyatake,Nobuyuki Kasahara & Hisanobu Kanamaru |
|
626 |
Variation of Detailed Burr Shape and of Die Wearing in Punching Process by Using Turret Punching Press | Takashi Iizuka,Keigo Tsuji,Nobuo Hatanaka & Norio Takakura |
|
627 |
Blanking Noise Reduction by Using Die with Counter Pressure | Kunlachart Junlapen,Nobuhiro Koga & Ken Mizuochi |
|
628 |
Influence of Shearing Contour on Burr-Free Shearing of Thin Metal Sheet | Nobuhiro Koga,Ken Mizuochi & Kunlachart Junlapen |
|
629 |
Effect of tool condition on cutting processability of laminated polycarbonate sheets | takahashi takuya,nagasawa shigeru & fukuzawa yasushi |
|
630 |
Estimation of Cutting-Load with Low Cutting-Load Scissors | Takashi Iimura & Kenji Inoue |
|
631 |
Motion of Fiber after Cut by Hair Cutting Scissors | Kenji Inoue & Takashi Iimura |
|
Drawing・Straightening | ||
|
632 |
Effect of Reduction on Drawn Diameter in Tandem
Pass Drawing - Study of High Dimensional Accuracy of Drawn Bar I - |
Sonomi Shirasaki,Motoo Asakawa,Ryosuke Komami & Yuichi Tanaka |
|
633 |
Effect of Drawing Conditions on Drawn Diameter
in Tandem Pass Drawing - Study of High Dimensional Accuracy of Drawn Bar Ⅱ - |
Ryosuke Komami,Motoo Asakawa & Sonomi Shirasaki |
|
634 |
Improvement of Straightness in Tension Annealing for Superfine Wire | Motohiko Urabe,Motoo Asakawa,Satoshi Kajino & Ryota Hamada |
|
635 |
Effect of wire diameter wire on drawing with reentrant 2 rolls | senzaki yasunori,kuboki takashi & murata makoto |
|
636 |
Behavior of Tube Cross Section in Straightener | Yohei Yamaguchi,Tatuya Amano,Takashi Kuboki,Makoto Murata,Tomio Yamakawa & Kouichi Kuroda |
|
Material Model | ||
|
637 |
Viscoplastic Behaviour of Acrylic Adhesive in Butt-joint under Cyclic Torsion and Its Modeling | Noriaki Mizutani,Tetuya Yoshida,Michihiro Takiguchi,Hiroshi Hamasaki & Fusahito Yoshida |
|
638 |
Modeling of High Temperature Viscoplastic Deformation Behaviors for β Titanium Alloy | Michio Yamamura,Ryota Yamauchi,Wang Xiao teng,Hiroshi Hamasaki,Fusahito Yoshida,Keisuke Nagashima & Takashi Maeda |
|
639 |
Numerical Simulations of Cyclic Plastic Deformation on Steels Based on the Theory of Poly-Crystal Plasticity. | Koushirou Kitayama,Hiroshi Hamasaki,Takeshi Uemori & Fusahito Yoshida |
|
Deep Drawing ・Stretch
Forming | ||
|
701 |
Deep Drawing of Magnesium Alloy Thin Plate | Shin-ichi Matsuoka,Takanori Nakagawa,Tsutomu Murai & Fumiaki Nakagawa |
|
702 |
Superplastic Forming of AZ61 Magnesium Alloy Extrusion | Toru Jinishi,Toshiyuki Naganuma,Nobuyuki Suzuki,Toru Takahashi & Tsutomu Murai |
|
703 |
Effect of Temperature and Strain-Rate on Non-proportion Stretch-Forming of AZ31 Magnesium Alloy Sheets | Yosuke Uekawa ,Takashi Katahira,Tetuo Naka,Takeshi Uemori,Fusahito Yoshida,Masahide Kohzu & Kenji Higashi |
|
704 |
Prediction of FLD for AZ31 Magnesium Alloy Sheets under Warm Non-proportional Stretching | Takashi Katahira,Yosuke Uekawa,Tetsuo Naka,Takeshi Uemori,Fusahito Yoshida,Masahide Kohzu & Kenji Higashi |
|
705 |
Deep Drawing and Redrawing of Magnesium Alloy AZ31 Plate | Kunio Isobe |
|
706 |
Thermo-machanical treatment for improvement of the cold formability of 6%Zn-4%Al-0.5%Ca-Mg alloy sheet materials | Masahito Katoh,Kotaro Hanada,Yoichi Murakoshi & Kunio Matsuzaki |
|
707 |
Elasto-plastic deformation behavior of 5000 and 6000 series aluminum alloy sheets and its modeling | Shohei Tamura,Satoshi Sumikawa,Kohei Ogawa,Hiroshi Hamasaki,Takeshi Uemori,Tetsuo Naka & Fusahito Yoshida |
|
708 |
In-process monitoring for press forming | Naoto Hagino,Junichi Endou,Shunji Katoh,Seiji Okudera,Masao Maruyama & Makoto Kubota |
|
709 |
Study of Seam joining Method in Forming a Deep Cup Using a Developed Blank | Shogo Waki,Satoru Kikunaga,Nobuo Hatanaka,Takashi Iizuka & Norio Takakura |
|
710 |
Development of a new sheet metal forming for making 3 dimensional shell structure with complex shape by using extrusion | Takashi Iizuka,Ryota Maeda,Li Ke & Norio Takakura |
|
711 |
Development of Forging Type Rapid Prototyping
System. (Generation of Tool Path Considering Deformational Process) |
Fumiya Murata,Naoki Asakawa,Masatoshi Hirao & Hidetake Tanaka |
|
712 |
Development of Forging Type Rapid Prototyping System (Accumulated Deformed Elements Model) | Yuta Abe,Naoki Asakawa,Masatashi hirao & Hidetake Tanaka |
|
713 |
Warm Redrawing of Stainless Steel | Aida Shuhei,Sugii Shingo,Makoto Tamura & Satoshi Katayama |
|
714 |
Development and Test Method of “Chlorine-Free” Metalworking Oil for Drawing and Ironing of “Stain-less Steel ” | Shigeki Kimura,Takeshi Yoshida & Naoto Shoji |
|
715 |
Effect of Forming Conditions on Hole-expansion Capability in High-Formability Ferritic Stainless Steel | Eiichiro Ishimaru & Akihiko Takahashi |
|
716 |
Spherical cup stretch-ability in hot stamping | Masahiro Nakata,Toshiya Suzuki,Kazuo Hikita,Kazuo Uematsu & Yozo Hirose |
|
Forging | ||
|
717 |
Springback simulation in sheet forging considering elastic deformation of dies and its experimental verification | Mitsuhiro Serizawa,Kuwabara Toshihiko,Imura Takaaki & Ando Bumpei |
|
718 |
Forging in the Low Load of Case Made Magnesium Alloy Sheet Using Servo Press | Mitsunobu Shiraishi,Yoshiaki Mori & Makoto Nikawa |
|
719 |
Development of Knowledge-Based Metal Flow Prediction System in Cold Forging | Masanobu Umeda,Shinichirou Yamazumi & Mure Yuji |
|
720 |
Development of Knowledge-Based Die Design System in Cold Forging | Masanobu Umeda,Yosuke Tsushima & Yuji Mure |
|
721 |
Eco-friendly puroduction engineering using die maintenance information. | takeshi inada |
|
722 |
Development of Upsetting-Extrusion Type Tribometer | Komiyama shinobu,Wang zhrgang,Tokunaga ryuichi & Yamaoka yuichi |
|
723 |
Evaluation of environmentally friendly lubricants for forging:Part2. | Tamotsu Nakamura,Yu Sumioka,Katsuyoshi Sakoda,Shinichi Miyano,Yuki Ishiizumi,Itaru Ishibashi & Masahiro Sekizawa |
|
724 |
Behavior of Lubricant Trapped within Concave Pocket during Upsetting | Akira Azushima,Takahiro Yoshimoto & Akira Yanagida |
|
725 |
Effect of strain ageing in upsetting | You You,Kuboki Takashi & Murata Makoto |
|
726 |
Isothermal Forging of NI-base Super Alloy | Yoshiki Yamada,Yusuke Yamaguchi & Kiyoyuki Ohuchi |
|
727 |
Decrease of Frictional Force Using Pulsating Load in Metal Forging | Tomoyoshi Maeno,Kozo Osakada,Ken-ichiro Mori & Akihiro Nakamura |
|
728 |
Prototyping of Ultrafine-grained Steel Plate by Free Forging Press of 3000ton-class | Tadanobu Inoue,Fuxing Yin,Kotobu Nagai & Tomoyuki Ochiai |
|
729 |
Influence of Compression Process on Internal Defect Behavior by Numerical Simulation | Takefumi Arikawa,Hideki Kakimoto,Youichi Takahashi,Tatsuya Tanaka & Yutaka Imaida |
|
730 |
Nano-order Observation of Forge Welding Boundary between Steel and Aluminum Alloy | Hirotaka Ogitani,Yoshinori Yoshida,Nobuki Yukawa,Takashi Ishikawa & Tomoaki Suganuma |
|
731 |
Control of Slide Motion in Hot Die Forging of Aluminum Alloy Billet | Hiroyuki Fujii,Ken-ichiro Mori & Masahiro Sato |
|
732 |
Development of the Model Workpiece Materials for Physical Simulation of Metal Forming Processes | Satoru Kuwaharada,Kenji Nakanishi,Yuji Mure & Yasumichi Matsumoto |
|
Theme Session:Optimization Method and Its
Application to ngineering Design and Metal Forming
Process | ||
|
733T |
Optimization Computation for Stamping Formobility and Springback Compensation using LS-DYA/LS-OPT | Ninshu Ma,Nobuhiko Sugitomo,Nielen Stander,Xinhai Zhu & Mike Burger |
|
734T |
Optimization Analysis of Thermomechanical Hot-stamping Process Using JSTAMP/NV | Bonyoung Ghoo,Yasuyoshi Umezu,Yuko Watanabe & Ninshu Ma |
|
735T |
Process Integration and Desin Optimization software and its application to plasticity | Hiroya Furuichi |
|
736T |
Recent Trend of Optimization Technology in Forging Process Simulation | Soo-Young Kim |
|
737T |
Die Shape Determination in Draw Bending Process Using the Moving Punch | Yuki Morishita,Shigeki Abe & Yasuhiro Sakamoto |
|
738T |
Control of Wrinkle and Twist-type Springback of Stepped-shape Beam by Optimizing Draw-bead Design | Shigeki Abe,Yuki Morishita,Yasuhiro Sakamoto,Hiroki Kondo,Ryutaro Hino & Fusahito Yoshida |
|
739T |
Evaluation of Multistage Drawing by Forming Limit Diagram (Optimization of Forming Process for Multistage Cylindrical Cup-Drawing) | Kazutake Uehara & Fumio Obata |
|
740T |
Optimum Design of Multi-Stage Deep Drawing Process in Consideration of Blank Size Minimization Using Numerical Optimization Method | Ryutaro Hino,Toshiya Hirooka,Fusahito Yoshida & Vassili V. Toropov |
|
741T |
Development of Perfect Simulation System on CAE
without Trial Working for Products (Manufacture of High Precision System Using Dispersion of Error Factors) |
Ikuo Tanabe & Jyunnosuke Mizutani |
|
742T |
Robust tension leveling process design by means of stochastic optimization | H.Hamasaki,R.Hino,Vassili V. Toropov & F.Yoshida |
|
743T |
Effect of Fracture Criterion on Optimization of Sheet Metal Forming Condition(2nd Report: Comparison of Optimization Results Using Several Fracture Criteria) | Atsushi Hirahara,Ryutaro Hino,Fusahito Yoshida & Vassili V. Toropov |
Copyright (C)1997- 2008 JSTP. All Rights Reserved. |