The Proceedings of the 2013 Japanese Spring Conference for the Technology of Plasticity |
Sheet Metal Press Forming | ||
101 | Development of a CAE system for Springback (4th report) | Tetsuo Oya & Naoyuki Doke |
102 | Effect of punch holes location on spring-back in sheet metal forming of punching metal sheet | Satoshi Kitaura,Takashi Ueda,Yuji Kawata,Yasuhide Kaji & Shinichi Enoki |
103 | FEM Analysis for Mechanism of Springback Reduction by Stroke Returning Deep Drawing in Hat Channel with High-Tensile Steel Sheets | Masayuki Asakura,Taro Geka,Takuma Kiso,Masato Takamura,Takashi Sugiyama & Motoo Asakawa |
104 | Reduction of Twist and sidewall curl in Hat Channel for High-Tensile Steel Sheets by Stroke Returning Deep Drawing | Takuma Kiso,Taro Geka,Masayuki Asakura,Takashi Sugiyama,Masato Takamura & Motoo Asakawa |
105 | Material modeling considering tension/compression asymmetry of flow stresses; 2nd report: Springback analysis | Nobuyasu Noma,Toshihiko Kuwabara & Rahul Kumar Verma |
106 | Springback analysis of high tensile strength steel sheet using complex-step derivative method | Satoshi Okada,Takeshi Uemori,Taro Tokuda,Tetsuya Yoshida,Michihiro Takiguchi & Fusahito Yoshida |
107 | Effects of Piercing Conditions for Initial Hole on Fracture Behavior of High-Strength Steel Sheet Caused by Flat-Bottomed Cylindrical Punch Forming | Yasuhiro Ito,Yoshiaki Nakazawa & Ryuichi Nishimura |
108 | Effect of thickening of hole edge on fatigue strength of punched ultra-high strength steel sheet | Purwo Kadarno,Ken-ichiro Mori,Yohei Abe & Tatsuro Abe |
109 | Accuracy of yield function determined using multiaxial tube expansion test method | Ryotaro Enatsu,Toshihiko Kuwabara & Yanis Korkolis |
110 | Continuous Measurement of Multiaxial Tube Expansion Test Using Optical Deformation Measurement System | Tomoyuki Hakoyama & Toshihiko Kuwabara |
111 | Material modeling of cold rolled IF steel sheet based on multiaxial tube expansion test and hydraulic bulge forming simulation | Shuuhei Kegasawa,Daisaku Yanaga,Toshihiko Kuwabara & Jun Chen |
112 | Variable and Steady Semi-Open-Loop Press Manufacturing by Intermittent Forced Displacement Function | Shigeo Kotake & Kazunori Yagi |
113 | Identification of a Flow Stress Curve and a Yield Function on Plate Tensile Tests | Masanobu Murata,Takeshi Nishiwaki & Yoshinori Yoshida |
114 | FEM Analysis of Uniaxial Tensile Deformation of Dumbbell-shaped Tensile Specimen in Thickness Direction Assuming Isotropic Material | Hayato Usui & Takashi Iizuka |
115 | Suppression of forming defects and variations using servo-controlled draw-beads | Masaki Kamihigashi,Nobuyasu Noma & Toshihiko Kuwabara |
116 | Effect of retained γ volume fraction on ductile fracture behavior | Shoichiro Asai,Takahiro Ishiguro,Eiji Abe,Nobuki Yukawa,Hiroshi Yoshida,Nobuhiro Fujita & Takashi Ishikawa |
117 | Effects of texture on twinning deformation of AZ31 magnesium alloy | Takashi Katahira,Syohei Hosokawa,Tetsuo Naka,Kohzu Masahide,Hiroki Adachi,Takeshi Uemori & Fusahito Yoshida |
118 | Cyclic Deformation and Transformation Induced Plasticity for SUS304 Steel | Hiroshi Hamasaki,Eiichiro Ishimaru,Tatsuya Ohno & Fusahito Yoshida |
119 | Effects of microstructure on room temperature formability of magnesium alloy sheets | Xinsheng Huang,Kazutaka Suzuki,Motohiro Yuasa,Yasumasa Chino & Mamoru Mabuchi |
120 | Crystal-plasticity finite-element analysis of magnesium alloy sheet with random crystallographic orientations | Takayuki Hama,Naohiro Hosokawa,Tsuyoshi Mayama & Hirohiko Takuda |
121 | Development of Chloride-free oil for ironing of stainless steel | Kimihiro Oono,Naoki Kajita,Kazuhiko Kitamura,Junichi Shibata & Tomohiro Takaki |
122 | Prediction of Surface Roughening in Micro Deep Drawing by Inhomogeneous FE Material Modeling | Tsuyoshi Furushima,Tomoko Nakayama,Ken-ichi Manabe,Sergei Alexandrov,Haina Lu,Donbin Wei & Zhengyi Jiang |
123 | Evaluation of Seizing Process for Pure Titanium by Galling Test | Takayuki Muranaka,Hiromu saito,Hideyo Miyoshi,Takeshi Kihara & Masaaki Otsu |
124 | Mechanism of Lubrication of Die Having Hetero-Surfaces in Ironing of Stainless Steel Cup | Yohei Abe,Fumihiro Hatashita,Takashi Shiba,Ken-ichiro Mori & Witthaya Daodon |
125 | Effects of Material Model on the Analysis Accuracy of Forming Simulation of Hemispherical Punch Drawing | Tomoyuki Sawada & Syuuhei Kegasawa |
126 | Material modeling of 5000 series aluminum alloy sheet based on biaxial tensile test and hydraulic bulge forming simulation | Junpei Kawaguchi,Toshihiko Kuwabara & Takeo Sakurai |
127 | Evaluation of Water Film characteristics in Deep Drawing with High-Pressured Water using Reynolds equation | Yuki Horikoshi,Takashi Kuboki,Makoto Murata,Makoto Tsubokura & Kazumi Matsui |
128 | In-situ measurement of 3-dimensional deformation during flanging of sheet metal using 2 borescopes | Zamzuri Hamedon,Ken-ichiro Mori & Yohei Abe |
Micro Forming | ||
201 | Theory of micro hydromechanical deep drawing and fracture limit | Hideki Sato & Ken-ichi Manabe |
202 | Effect of motion control on the micro-embossing process for accurate micro-texturing | Tatsuhiko Aizawa,Taichi Itoh & Tatsuya Fukuda |
203 | Static recrystalization of sigle crystal iron by means of microforimg test | Masahiko Yoshino,Kohei Ibuki,Shiro Torizuka & Akinori Yamanaka |
204 | Effect of Tool Surface Properties on Dry Frictional Properties of Ultra-thin Metal Foils | Tetsuhide Shimizu,Ming Yang & Ken-ichi Manabe |
205 | Fabrication of single crystal diamond tool bit by FIB processing and micro shaft cutting | Tomohiro Miyairi & Hiroyuki Noguchi |
206 | Study on nanofiber melt spinning using principle of centrifugal force | Hiroyuki Noguchi & Takuya Osada |
207 | Normal temperature compression processing of ceramic powders which uses micromold fabricated by FIB | Takuya Osada & Hiroyuki Noguchi |
208 | Dry Friction and Wear Properties of Micro-Textured DLC Thin Films | Tetsuhide Shimizu,Tai Kakegawa & Ming Yang |
Forging | ||
209 | Press Forging with Back Pressure on Servo Press | Kiichiro Kawamoto,Takeshi Yoneyama,Masato Okada & Junpei Chikahisa |
210 | Influence of Reduction in Area and Slide Speed on Dimensional Accuracy of Cold Backward Extrusion for Aluminum Alloy | Motoki Terano,Fang Guo,Takahiro Ishiguro,Eiji Abe,Nobuki Yukawa & Takashi Ishikawa |
211 | Shape Accuracy of Formed Hole in Pulse Forming for Deep Hole using Servo Press | Ryo Matsumoto,Jae-Yeol JEON & Hiroshi Utsunomiya |
212 | Development of a two-point servo press with a new mechanism using a fan-shaped support rod. | Kodaira Yuya,Nakayama Noboru,Kobayashi Nobuhiko,Kodaira Naofumi & Saijo Koichi |
213 | Plate forging of spur gear using load pulsation | Tomoyoshi Maeno,Yuki Ichikawa & Ken-ichiro Mori |
214 | Material Data for the Kinetics of Microstructure Evolution under Hot Forming of SUS316 Stainless Steel | E.E.V. Dupin,M. Soltanpour,Akira Yanagida & Jun Yanagimoto |
215 | Microstructure of AZX911 Magnesium Alloy Continuous Cast Bar during Hot Forging | Naobumi Saito,Hajime Iwasaki,Kazuo Kanbara,Tsunehisa Sekiguchi & Naoaki Miyamoto |
216 | Effects of Surface Texture Formed on Punch Surface on Surface Quality of Aluminum Product in Plane Strain Multi-gate Backward Extrusion | Shunpei Kamitani,Yoshihiro Kikuchi,Kenta Yasunaga & Yong-Ming Guo |
217 | Evaluation of Lubrication Performance on Aluminum Alloy Cold Forging. (7th report) | Masanobu Tsukamoto,Yoshihiro Sagisaka,Itaru Ishibashi,Toshinari Nakakura,Tamotsu Nakamura & Kunio Hayakawa |
218 | Combined Effects of Lubricants and Nitriding Tool for Warm Forging of Steel | Kazuhito Asai & Kazuhiko Kitamura |
219 | Effect of spraying time on solidification morphology of white type lubricant- Factors in forming uniform lubricant film for hot forging 4- | Yoshinari Tsuchiya,Ryousuke Tsutsumi & Zhigang Wang |
220 | In-situ observation on white type lubricant film at tool-work interface by upsetting of hot steel work-Attempt of new methodology for evaluation of tribo-characteristics of white type lubricants 2- | Ryousuke Tsutsumi,Yoshinari Tsuchiya & Zhigang Wang |
221 | Fatigue life prediction for cold forging die | Yasuhiro Maeda,Eiji Abe,Motoki Terano,Takahiro Ishiguro,Nobuki Yukawa,Takashi Ishikawa & Takuma Okazima |
222 | Improvement of forging process design by using ductile fracture evaluation system | Satoshi Kubota,Soo-Young Kim & Chou Kyoku |
223 | Influence of Closed Conditions on Folw and Load in slit Upsetting | Ayato Mizuno,Kazuhiko Kitamura & Kei-ichi Mastunaga |
224 | Influence of Moisture Content on Transmittance of Transparency Compressed-Wood | Kimiyoshi Kitazawa & Nobuyuki Amemiya |
Ultrasonic Process | ||
225 | Fundamental Study on Ultrasonic Microforging (2nd Report) Investigation of die forging of complex shape |
Masahiko Jin,Koudai Touke & Mitsuru Kodama |
226 | Fundamental Study on Precision Ultrasonic Welding of Thin Sheet and Foil | Masahiko Jin,Wataru Nakadachi,Hidenari Kanai & MItsuru Kodama |
227 | Fundamental Studies on Bonding of Ultra-thin Metal Foils by using Ultrasconic Axial Vibration | Ryo Yamaguchi,Tetsuhide Shimizu & Ming Yang |
228 | Development of Simulator for Prediction of Real Amplitude in Vibration Forming | Tadatsugu Yoshida |
Theme Session:Current Status of Hot & Warm Forming for Tubing and Sheet Metals | ||
301 | Effect of blankholder in hot stamping of hat-shaped part | Tomoyoshi Maeno,Yuzo Yanagita,Ken-ichiro Mori & Takahiro Murayama |
302 | Effect of Timing of Blankholding on Formability in Hot Stamping of Cup | Tomoyoshi Maeno,Ken-ichiro Mori & Masaki Fujimoto |
303 | Deep Drawability in Hot Stamping Process with Clearance of Flange Part in a Die | Kazuhisa Kusumi,Naruhiko Nomura,Masahiro Nakata,Shuji Yamamoto,Masayuki Abe & Masayoshi Suehiro |
304 | Evaluation of Lubricant for Hot Stamping Using Hot Deep drawing Test | Akira Yanagida,Eitaro Komatsu,Hironori Sasaki & Akira Azushima |
305 | Hotstamping of heat-treated alminum alloy sheet using resistance heating | Ken-ichiro Mori,Ryousuke Yachi,Tomoyoshi Maeno,Kazuyoshi Fujii & Takeshi Nukaya |
306 | Prevention of Hardening of Punching Region of Sheet in Hot Stamping Using Resistance Heating | Ken-ichiro Mori,Tomoyoshi Maeno & Takuya Suganami |
307 | Delayed failure on surface hot-trimmed during die-quench process | Takashi Matsuno,Yoshihito Sekito,Tamaki Suzuki,Kaoru Kawasaki & Masayoshi Suehiro |
308 | Influence of Shape Retaining Force on Forming Performance in Hot Stamped and Die-quenched Steel Sheet Part | Seijiro Maki,Yoshihiro Kusunoki & Eitoku Nakanishi |
309 | Warm Formability of Steel Sheets in Various Deformation Modes | Masahiro Kubo,Hiroshi Yoshida,Tohru Yoshida,Masayoshi Suehiro,Chisato Wakabayashi & Junichi Hamada |
310 | Development of Three-Dimensional Hot Bending and Direct Quench (3DQ) Mass Processing Technology 5 -Effect of Strain Rate Dependent of Flow Stress and Transformation Strain in 3DQ FEM simulation- | Hiroaki Kubota,Atsushi Tomizawa,Kenji Yamamoto & Nobuhiro Okada |
311 | Dieless Bellow Forming for Metal Tubes | Zicheng Zhang,Tsuyoshi Furushima,Ken-ichi Manabe,Kazuo Tada & Osamu Sasaki |
312 | Blanking of Spur Gear Using Local Resistance Heating | Ken-ichiro Mori,Makoto Tsuchiya,Tomoyoshi Maeno,Takuji Watanabe & Tatsuhiro Nanya |
Extrusion | ||
313 | Effect of Fin Shapes on Forming Characteristic in Extrusion with Helical Fins | Mitsunobu Shiraishi,Shinichi Tonomura & Yasuyuki Suga |
314 | Small Billet Extrusion of Sintered Porous Copper Sheet | Yukinori Taniguchi,Kento Shirouchi,Hiroaki Tsutsumi,Mitsunori Ozaki & Hirotsugu Shimada |
315 | Possibility and problems in production of long parts by sequential extrusion of wood using flow forming | Tsunehisa Miki,Hiroyuki Sugimoto,Ichinori Shigematsu,Kozo Kanayama,Kiyoharu Hashimoto,Junichi Ikeda & Syoichi Tsuiki |
Tube Forming | ||
318 | FEM Evaluation of Die Half Angle Effect in Nosing Process Using Relieved Die | Mitsumasa Abe & Takashi Kuboki |
319 | Rotary Tube-End Nosing Operation with Off-Centered Tool for Eliminating Wrinkling in Welded Stainless Steel Tube-End Nosing Parts | Hiroki Okuda & Kimiyoshi Kitazawa |
320 | Formability of Multi-process Hydroforming with Unidirectional Expansion | Manabu Wada,Masaaki Mizumura & Hiromitsu Kaneda |
321 | Vibration Analysis of Excitation Mandrel in Draw Bending of Tube | Tadatsugu Yoshida |
322 | The effect of torsion and heat treatment on press bendability of AZ31 magnesium alloy extruded tube | Osamu Hasegawa & Tetsuo Aida |
323 | Form rolling processes for making a flange in pipes with a small diameter | Isao Kuboki & Masahiro Ushikubo |
Bending | ||
325 | Prediction Accuracy of Bending Angle in V-bending Process of Plate by FEM | KHAMT NARANBAATAR,Makoto Murata,Takashi Kuboki & Yingjun Jin |
326 | Texture Control for Aluminum Sheets by Using CO2 Laser Apparatus | Yuko Matayoshi,Takashi Sakai,Yingiun Jin & Jun-ichi Koyama |
327 | Fracture Prediction for Sheet Metals subject to Draw-bending using Forming Limit Stress Criterion | Masazumi Saito & Toshihiko Kuwabara |
328 | Development of Bending Using Cross-Sectional Deformation of Extruded Shapes | Noah Utsumi & Masashi Yoshida |
Theme Session:Processing and the commercialization technology of a tube and the wire rod to enhance. | ||
401 | Modeling by MATLAB for Bending of Glasses Frame Rim,High Precision Roll Bending of Deformed Titanium Alloy Wire for Glassframe(5th report) | Masami Matumura,Yoshinori Sasaki,Masaaki Ootsu,Taiki Tanaka,Yuichirou Sekine & Motoo Asakawa |
402 | Suggestion and Verification Countermeasures of Processing Defects by Experimental and FEM Analysis, High Precision Roll Bending of Deformed Titanium Alloy Wire for Glassframe (6th report) | Yuichiro Sekine,Natsuki Kato,Yuki Takebe,Shuzo Matsuo,Masami Matsumura,Yoshinori Sasaki & Motoo Asakawa |
403 | Special Tube Production by Bunch Drawing and Fluid-Mandrel Drawing. | Kazunari Yoshida,Takaaki Komatsu & Daichi Yokomizo |
404 | Improvement of ductility of aluminum drawn wire by alternate drawing | Kota Doi & Kazunari Yoshida |
405 | Improvement of Straightness and Decreasing Wave by Using Dowel with Rotational Roll | Kota Sakumoto,Motoo Asakawa,Natsuki Kato,Kazuki Tsurumi & Tomio Kanno |
406 | Straightening Tungsten Fine Wire with Rotational Blade Straightener | Shuichi Chinone,Motoo Asakawa,Natsuki Kato,Kazuki Tsurumi,Kota Sakumoto & Tomio Kanno |
407 | Elastic-plastic FEM Analysis of Twist Straightening | Natsuki Kato,Motoo Asakawa,Kazuki Tsurumi,Kota Sakumoto & Tomio Kanno |
408 | Influence of the Shape of Deformed Bars on the Bending Workability. | Kiyoshi Uwai,Yasuhiro Oomori,Takashi Iwamoto & Shigeru Endo |
410 | Flow stress of high carbon steel in high speed wire drawing | Shinya Kojima,Motoo Asakawa,Takahiro Shirakawa & Ryuta Kawaguchi |
411 | A analytical method of metal forming of a bar considering aging | Takashi Kuboki |
412 | The wire drawing technique for strengthening in high carbon steel wire. | Tadakuni Hori,Motohiro Nakano,Atsushi Sasaki & Hiroshi Utsunomiya |
413 | Ductile Fracture Evaluation in Drawing by the Void Model for Ferrite-Pearlite Steels | Kazutake Komori |
414 | Relationship between microstructures and mechanical properties of medium carbon steel for cold forging with isothermal transformation treatment | Makoto Okonogi,Daisuke Hirakami & Hiroshi ooba |
415 | Atomic-level Modeling on Drawing of Iron and Steel Wire: Diffusion of Carbon Atom and Deformation in Cementite Microstructure | Ken-ichi Saitoh,Youhei Sameshima,Takuya Okada & Shuhei Daira |
Shearing | ||
418 | Trimming of high tensile strength steel sheets | Ying Chen & Nobuhiro Koga |
419 | Smooth piercing of ultrahigh-strength steel sheet by the use of press-shaving | Tomio Shionome,Masao Murakawa,Fumitoshi Komuro,Kenta Nakamura,Giichirou Muro & Nobuhiro Koga |
420 | Delayed fracture on the sheared surface of high-strength steel sheets | Fumitoshi Komuro,Masao Murakawa,Tomio Shionome,Kenta Nakamura,Giichirou Muro & Nobuhiro Koga |
421 | Direct Continuous Punching of Inclined Ultra-High Strength Steel Sheets | Yohei Abe,Yasunari Okamoto & Ken-ichiro Mori |
422 | Effect of Punching Speed on Surface Quality of Sheared Edge Obtained by Punching Using Punch Having Small Corner Radius for Die Quenched Steel Sheets | Youhei Abe,Keishiro Nakanishi & Ken-ichiro Mori |
423 | Analysis Using Arc Approximation about Shape Variation of Die Shoulder in Initial Abrasion Stage of Punching Process | Takashi Iizuka & Daichi Sakamoto |
424 | Influence of material properties on piercing process of hollow forging product | Takahiro Ishiguro,Takako Kikuchi,Eiji Abe,Motoki Terano,Nobuki Yukawa & Takashi Ishikawa |
425 | The Characteristics of Fine Blanking Technique using Servo Press Machine | Tomohiro Tsuruya & Shinya Honda |
426 | Algorithm for shearing force and motor power in link type crop shear of plate mill | Toshio Watanabe |
427 | Physical simulation on the effect of large shear deformation on the evolution of microstructure | Jinyu Lin,Ismail Tirtom,Kei Shimojima,Mo Kou,Sumio Sugiyama & Jun Yanagimoto |
Rolling | ||
501 | Possible Chattering Model from Localized Energy Transfer in Coupled Oscillations among Multi Cold Rolls | Shigeo Kotake |
502 | Oil film thickness of lubricant in cold pilgering | Hideaki Abe,Tetsuya Iwamoto & Hiroyuki Hara |
503 | Effect of lubrication in skin-pass rolling of thin steel sheets with bright work rolls | Hideo Kijima |
504 | Calculation system of pass schedule and motor power of mill stands in round bar rolling | Toshio Watanabe & Tetsuya Kuji |
505 | Effect of Rolling Condition on Mechanical Properties and Microstructure of High Strength Magnesium Alloy | Masafumi Noda,Naoto Sakai & Kunio Funami |
506 | Thermal Properties of Cr-Cu Rolled Material and Cr-Cu/Cu Clad and Rolled Material | Hoshiaki Terao,Hiroshi Wada,Hideaki Kobiki,Hiroki Ota & Naoyuki kanetake |
507 | Orientation and Densification Behavior of Plate-like Ceramic Particles in Powder Rolling with Differential Roll Speed | Mutsumi Kawahara,Wang Zong,Kazunari Shinagawa & Feng Qi |
508 | Microstructure Evolution of a Zn-Al Eutectoid Alloy by Multipass Hot-Rolling | Toshiaki Manaka & Goroh Itoh |
Theme Session:New approaches in roll forming technology for new needs in manufacturing | ||
510 | Effect of insert position of curved sheet into dies in fabrication process of small diameter tube | Hidenori Yoshimura,Yutaka Mihara,Kousuke Yamamoto & Takuo Nagamachi |
511 | Development of the Forming Method for Welded Pipe -Orbital Die Forming- 2nd Report | Chie Oishi,Jilong Yin,Tomoyasu Nakano,Feizhou Wang & Manabu Kiuchi |
512 | Finite Element Analysis of the High Frequency Electric Resistance Welding Phenomenon | Takatoshi Okabe,Akira Kawanishi,Sota Goto,Masatoshi Aratani,Shunsuke Toyoda & Hideto Kimura |
513 | Finite element simulation of roll forming of seam welded pipes 10th report | Keinosuke Iguchi,Yousuke Matui,Takayuki Hama,Hirohiko Takuda & Yukihisa Kuriyama |
514 | Deformation in cut section of roll-formed product (5th report) | Takuo Nagamachi |
515 | Deformation in cut section of roll-formed product (6th report) | Siti Nadiah binti Mohd Saffe,Takuo Nagamachi & Hiroshi Ona |
Incremental Forming | ||
516 | Mechanical Properties of Incremental-Flatted Steel Sheets | Kimiyoshi Kitazawa,Motoaki Nisibu,Masashi Komatsu & Mizuki Yoshigoe |
517 | Application of incremental forming process using elastic base plate for steel sheet | Nobuyuki Suzuki,Issei Minamiura & Shinichi Yoshioka |
518 | Temperature Measurement at Forming Point in Friction Stir Incremental Forming | Masaaki Otsu,Takuya Kao,Yosuke Katayama & Takayuki Muranaka |
519 | Effect of Relative Velocity between Tool and Sheet on Formability in Friction Stir Incremental Forming | Masaaki Otsu,Yosuke Katayama & Takayuki Muranaka |
520 | Sheet Metal Bending by Laser Peen Forming with Femtosecond Laser. (7th report) | Yoshihiro Sagisaka |
High Energy Rate Forming | ||
521 | Experiment of Joining Method Using Impact Shearing | Minoru Yamashita,Tatsuya Tezuka,Toshio Hattori & Joji Sato |
522 | Development of energy absorbing material for landing gear of smart lander using bored aluminum foam | Tomoyuki Sekino,Koichi Kitazono,Eiichi Sato & Shujiro Sawai |
523 | Influence of cross-sectional shape on dynamic axial compressive deformation of aluminum square tubes | Makoto Miyazaki,Masashi Yamaguchi & Hiroki Nishizawa |
524 | Experiment and Simulation of Electromagnetic Bulge Forming of Stainless Sheet Metal | Shigeyoshi Nagano,Tetsumaro HIroi,Masaki Ishibashi & Ken-ichi Manabe |
525 | Magnetic Pressure Seam Welding for Aluminum and Various Sheet Metals (3rd report) | Makoto Miyazaki & Daisuke Kuroda |
526 | Magnetic Pulse Welding on Both Sides of Flat One-Tern Coil | Tomokatsu Aizawa,Okagawa Keigo & Ishibashi Masaski |
527 | Simultaneous Joining of Five Aluminum Sheets by Magnetic Pulse Welding | Masaki Ishibashi,Keigo Okagawa,Tomokatsu Aizawa & Eiki Kabasawa |
Joining | ||
601 | Cold forge bonding of Steel and Aluminum Sheets | Yuri Miwada,Eiji Abe,Motoki Terano,Takahiro Ishiguro,Nobuki Yukawa,Takashi Ishikawa & Tomoaki Suganuma |
602 | Simultaneous Joining of Three Aluminum Sheets with Different Thickness by Magnetic Pulse Welding | Keigo Okagawa,Masaki Ishibashi,Tomokatsu Aizawa & Eiki Kabasawa |
603 | Comparison between joint strengthes obtained by mechanical clinching and resistant spot welding in ultra-high strength steel sheet | Yohei Abe,Shoma Nishino,Toru Kato & Ken-ichiro Mori |
604 | Joining by Hemming of High Strength Steel | Yohei Abe,Yuji Murata & Ken-ichiro Mori |
605 | Relationship between Degradation and Microstructure in Tungsten and Molybdenum Electrodes for Fusing Joining | Syuhei Iijima,Goroh Itoh,Shingo Mukae & Nobuhide Itoh |
606 | Characteristics of New Solid State Bonding with Heating and Ironing | Akira Nozue,Akira Kanda,Hiroyuki Yamaguchi & Osamu Kimpara |
607 | Basic characteristics of high precision plastic flow joining method that does not use a punch. | Masatoshi Usui,Atsushi Shirayori,Mitiharu Narazaki,Hiroya Murakami,Nobuyuki Kawame & Yukinori Suzuki |
608 | Applicability of Adhesive-Plastic Deformation Hybrid Joining Process for Fiber Reinforced Thermosetting Plastic (FRP) and Metallic Thin Sheets | Zhequn Huang,Sumio Sugiyama & Jun Yanagimoto |
Theme Session:Formability and estimtion of machining accuarcy on laminated composite materials | ||
609 | Deformation Analysis of A-flute Corrugated Fiberboard on Rotary Creasing Process | Pusit Mitsomwang,Komiyama Yuki & Shigeru Nagasawa |
610 | Effect of bending and scoring velocity on repeated bending characteristics of creased paperboard | Shinya Ozawa,Shigeru Nagasawa & Yasushi Fukuzawa |
611 | Effect of both sides tool condition on creasing characteristics of corrugated board | Kou Ishibashi & Shigeru Nagasawa |
612 | Effects of normalized shearing strain, tracking angle, rubbering on bending-moment relaxation of creased paperboard | Nagasawa Shigeru & Shiga Yoshiaki |
613 | Pushing-cut characteristics of resin thin sheet stacked on grooved counter plate using saw blade | Akira Hine,Shigeru Nagasawa,Kei Watanabe,Isamu Katayama,Teruo Ogawa & Kenji Kabasawa |
614 | Effects of Two-Layer Simple Die on Braille Embossability to Boxboard | Norio Takatsuji,Takuya Miura,Tetsuo Yanase,Tetsuo Aida & Shingo Okita |
615 | Cutting Characteristics of paperboard by the servo hydraulic press | Shigekazu Suzuki & Syuuhei Yoshida |
CFRP | ||
616 | Anecdotal survey of carbon fiber reinforced plastic molding parts for car | Minami Kimura |
617 | Isothermal forming of CFRTP sheet by penetration of hemispherical punch | Hidenori Aoki,Koichi Sugihara & Sachihiro Isogawa |
618 | Square Cup Forming of Carbon Fiber Reinforced Thermoplastic Composite | Daichi Tatsuno,Takeshi Yoneyama,Takumi Ito,Shoji Hineno,Takashi Moriyasu,Shigenori Nagashima & Masayuki Okamoto |
619 | Suitable Structure of Thermosetting CFRP for Plastic Deformation | Yu Uriya & Jun Yanagimoto |
620 | Finite Element Analysis and Evaluation of Dimension Accuracy of Sheet forming of Carbon Fiber Reinforced Thermo Plastic Plate | Kunio Hayakawa,Shotaro Hinoue,Tamotsu Nakamura,Kunimasa Muroi & Tohru Yamada |
Material Property | ||
621 | Consolidation Behavior of High Strength Aluminum Alloy Chip Waste Prepared by Compressive Torsion Processing | Yuji Kume,Ryuichi Morimoto,Makoto Kobashi & Naoyuki Kanetake |
622 | Specimen Size Effect on Al-Fe Precipitates Refinement Produced by Compressive Torsion Process | Kei Uchida,Yuji Kume,Makoto Kobashi & Naoyuki Kanetake |
623 | True stress-true strain behavior analysis of ultrafine grained steel by image analysis tensile test. | Shiro Torizuka,Toshihiro Hanamura & Shohei Enokida |
624 | The effect of process condition for material properties of stainless steel deformed by ECAP | Koshiro Aoki |
625 | Evaluation of Additional Plastic Deformation from Asymptotic Anhysteresis of Residual Magnetization | Shigeo Kotake,Hirou Nozaki,Yasuyuki Suzuki & Kawamura Takahiro |
626 | Evaluation of Mechanical Properties and Effect of Heat Treatment for Medical Platinum Alloy | Akio Segawa |
627 | Forming of roll cast aluminum alloy clad strip at semisolid condition | Toshio Haga & Takuya Ishihara |
628 | Measurement of Plastic Deformation Behavior of Sheet Metals Using Tube Torsion Test (2nd Report: Measurement of the Bauschinger Effect) | Shunsuke Iizuka & Toshihiko Kuwabara |